Whirlpool RH2000 Series Kurulum Talimatları - Sayfa 4

Havalandırma Davlumbazı Whirlpool RH2000 Series için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Whirlpool RH2000 Series 5 sayfaları. 30" vented custom series range hood
Ayrıca Whirlpool RH2000 Series için: Kurulum Talimatları (5 sayfalar), Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu (7 sayfalar), Kurulum Talimatları (5 sayfalar)

Sayfayı Yazdır

cabinet

To vent through

the roof or wall, mark 5-3/4"

and 6-1/4" in from back wall along the

centerline

on underside

of cabinet,

Use

these points as centers

to draw 7-1/8"

circles on underside

of cabinet,

Use a saber saw to cut the openings

for the

vent system, Repeat for the underside

the top of the cabinet,

This will create

slotted

openings

which

makes it easier to

install the vent system,,

Install vent system through

the vent

m opening

in upper cabinet

or wall,

Complete

venting

system according

method

needed,

See "Venting

requirements,"

Use caulking

to seal exterior

wall or roof opening,

If roof or wall cap does not

have a damper,

install damper

(supplied

with hood) in vent system to

prevent

air from flowing

back into vent

system,

If roof or wall cap has a damper,

Do Not use

damper

blade supplied

with range hood,

Do Not turn on power

until

m installation

is complete.

Run

wiring through

wall or cabinets

according

to the National

Elecfrbal

Code

and local

codes and ordinances,

Use caulking

to seal

ceiling

or outside wall opening,

four keyhole mounting

screw slots marked

on the cabinet

bottom,

keyho

Check

that

,?;--JA

o,,,o,.

front of hood

screw

Lift range hood into final

m position,

feeding

electrical

wire

through

wiring opening,

Tighten mounting

screws to cabinet,

making

sure mounting

screws are in narrow neck of slot,

Electrical

Shock Hazard

Disconnect

power before making

electrical

connections.

Connect

ground wire to green ground

screw in terminal

box.

Failure to do so can result in death or

electrical

shock.

Panel C

white

For models

requRing

dRect wiring:

Connect

the white and black wires of the

power

supply cable

to the white and black

leads in the range hood with twist-on

connectors,

Connect

the power

supply grounding

wire

to the green,

grounding

screw inside the

range hood terminal

box,

Use caulking

to seal wire opening,

Replace

terminal

box cover,

For cord

connected

models:

EJectrica! Shock Hazard

Plug into a grounded

3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions

can

result in death, fire, or electrical

shock.

For your personal

safety, this range hood

must be grounded,

To minimize possible

shock hazard, the cord must be plugged

into a mating,

3-prong,

ground-type

outlet,

grounded

in accordance

with National

Electrical

Code, ANS!/NFPA 70 - latest

edition*

and all local codes and

ordinances,

If mating outlet is not available,

if is the

responsibility

and obligation

of the customer

to have a properly

grounded,

3-prong

outlet installed by a qualified

electrician,

Do not use an extension

cord,

Using a U.L.-listed

power

supply

cord-connection

kit:

Follow Power Cord Kit instructions

for

connecting

wiring.

Replace

terminal

box cover,

For models

with a factory

installed

power

cord:

Plug power

cord into grounded

3-prong

outlet,

Turn power supply on,

Copies of standards listed may

be obtained from:

" National

Fire Protection

Association

Bafterymorch

Park

Quincy,

Massachusetts

02269

make reinstalling

your

range hood inanother

home

as easy as the first

installation.

of tan e

For best results, turn range hood fan ON at

beginning

of cooking

and allow it to run

until all smoke and odors are removed

from

room,

To turn fan ON and OFF:

Press fan control to turn fan on and off and

adjust fan speed,

Speed may be increased

or decreased

anytime

during range hood

operation,

To turn range hood light ON and OFF:

Press light control to turn light on or off, Light

may be turned

off or on anytime

during

range hood operation,

Care of

Fitter/light

lens:

For best results, remove

and dean

often,

To remove

filter/light

lens:

tilter tab

Pull firmly on filter tab to remove

filter/light

lens from range hood,,

To clean

filter/light

lens:

Place filter/light

lens in dishwasher

or hot

sudsy wafer to dean,

To reinstall filter/light

lens:

Place edge

of filter/light

lens in opening

that right side is above

flange

and tab

faces downward,

Press filter/light

lens into

position,

When it's time to replace

your

aluminum

filter/light

lens:

1, Model series RH2000X:,

Order Filter/Light

Lens no, 883149

2, Call Whirlpool's Telesales line at

1-800-442-9991

3, Give the Telesales Representative

the

part number

needed,

4, The Representative

will give you the

current price,

5, Place your order using your Master

Card ®_, V isa ®_ or Discover ®) c redit card,

6, If you wish: mail a check

or money order

to:

Whirlpool

Corporation

1900 Whirlpool

Drive

LaPorfe, IN 46350-9980

Attn: Accessory

Accounting

Be sure to ask the Telesales

Representative

about

the wide variety

other Whirlpool

Product Accessories,

To clean

fan motor:

Every three years lubricate

each

motor

bearing

with a few drops of oil to help

prolong

motor life,

Clean exterior of motor with a damp

cloth

and grease-cutting

detergent,

Exterior surfaces

Clean the range hood with a mild

detergent

and soft cloth, Do Not use

abrasive

cleansers

or steel wool pads,

Light

Do Not use bulb larger than 60 watts in light

socket,

Light bulb is not included,