Whirlpool RH2000 Series Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu - Sayfa 3

Havalandırma Davlumbazı Whirlpool RH2000 Series için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu indirin. Whirlpool RH2000 Series 7 sayfaları. 30" vented custom series range hood
Ayrıca Whirlpool RH2000 Series için: Kurulum Talimatları (5 sayfalar), Kurulum Talimatları (5 sayfalar), Kurulum Talimatları (5 sayfalar)

Sayfayı Yazdır

Venting requirements

Horizontal wall venting

Now start...

Vented models only

Non-vented models cannot be converted to vent.

With range hood in kitchen.

Slide cardboard

or hardboard

under range

before moving range across floor to prevent

damaging

floor covering.

Cover countertop,

cooktop or set-in range

with a thick, protective

covering to prevent

damaging

countertop.

Venting

system must terminate

to the

outside.

3-l/4"

x 10"

through

the wail

Do not terminate

the duct in an attic or

other enclosed

space.

Do not use four-inch

laundry-type

wall

caps.

Do not use plastic

duct.

Duct needed for installation

is not included.

Backdraft damper supplied with product

must be used. If roof or wall cap has a

damper, do not use damper supplied with

hood. Use metal duct only. Rigid metal duct

is recommended.

Determine

which

outside

venting

method

you need to use.

The length

of the duct and number

elbows

should be kept to a minimum

provide

efficient

performance.

The size of

the duct should

be uniform.

Do Not install

two elbows

together.

Use duct tape to seal

all joints in the duct system. Duct can

terminate

either through

the roof or wall.

Use caulking

to seal exterior

wall or roof

opening

around

exhaust

hood. For the most

efficient

and quiet operation,

it is

recommended

that the range

hood

vented

vertically

through

the roof using 7"

round duct.

Figures l-4 show common

venting

methods

and what types of materials

are needed.

wail cap

24!l

W Disconnect

and move freestanding

range from cabinet

opening

to provide

easier access to upper

cabinet

and rear

wall. Put a thick, protective

covering

over

cooktop,

set-in range or countertop

protect

from damage

or dirt.

W If your range hood

is a vented-only

model, determine

which

venting

method

(roof or wall venting)

you need to use.

Figure 3

roof cao

7" min. diameter

round duct

eibows~--~--i-~i:::i.~

If your range hood is a non-vented-

(recirculating)

only model, go to Step 3a,

Panel D.

3-l/4"

x 10" to round

3-l/4"

x 10" to round

duct transition

Figure 4

To install a

vented-only

model

fnstalation:

Recommended

duct length

Use 3-l /4" x lo" or 7" duct with a maximum

length

of 26 feet for duct system. For best

performance,

use no more than three 90"

elbows. To calculate

the length

of system

you need, add the equivalent

feet for each

duct piece

used in the system. See the

following

examples.

3- l/4" x lo" duct system

Vertical roof venting

roof cap

7" round vent

knockGuts

knockouts

W Remove

knockout

from the wirina

3-l 14" x 10"

eibow ~~KiI13e~

h. 1 - 90" elbow

= 5

ft.

8 feet straight

= 8

ft.

1 - wall cap

= 0

ft.

Length of 3-l/4"

lo" system

=13

ft.

66"

\'p7"'

--. .:

opening

(top or rear) to be used.

For rectangular

venting,

remove

only the

3-l /4" x lo" rectangular

opening

knockout

for the venting

method

(roof or wall) you

Figure 1

Recommended

standard fittings

have selected.

Vertical roof venting

roof cap

terminal

box

cover

3-114" x 10" 90"

3-l/4"

x 10" fiat

3-l/4"

x 10" wail

elbow = 5 ft.

elbow = 12 ft.

cap = 0 ft.

3-l/4"

x lo"

through

the roof

i+Q,

66"

7" duct system

9VeibMF6ft.-q,FP

'3-l/4"

x lo"

damper

W Remove

terminal

box cover from

Maximum length

= 26

feet

1 - transition

= 4.5 ft.

range hood.

3-l/i'x

lo"

to 7"

transition

2 - 90" elbows

1 - wall cap

8 feet straight

=lO

ft.

= 0

ft.

= 8

ft.

Excessive Weight Hazard

Use two or more people to move and

install range hood.

Failure to follow this instruction

can

result in back or other injury.

Length of 7" system

= 22.5 ft.

Figure 2

Recommended

standard fittings

keyhole

slot

front

of hood

W Lift the ranae

hood

into final

3-114" x 10" to 7"

90" elbow = 5 ft.

45" elbow = 2.5 ft.

7" wail cap = 0 ft.

position

and center.

Mark on the underside

of cabinet

the location

of the four keyhole

mounting

slots. Set range hood aside on a

protected

surface.

Panel B