Whirlpool RH8330 SERIES Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu - Sayfa 5

Havalandırma Davlumbazı Whirlpool RH8330 SERIES için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu indirin. Whirlpool RH8330 SERIES 7 sayfaları.

Sayfayı Yazdır

WARNING

Electrical Shock Hazard

Disconnect power before making

electrical connections.

Connect ground wire to green ground

screw in terminal box.

Failure to do so can result in death or

electrical shock.

to light

ground

bulbs

wires

power

white wires

supply

wiring

18.

For models requiring direct wiring:

Connect white wiring from the terminal box,

light harness and power supply wiring

together with twist-on connector.

Connect black wiring from the terminal box

to power supply wiring with twist-on

connector.

Connect the power supply ground wire and

the green ground wire inside the terminal

box under the terminal box ground screw.

Use caulking to seal wire opening.

Replace terminal box cover.

For cord connected models:

WARNING

Electrical Shock Hazard

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can

result in death, fire, or electrical shock.

For your personal safety, this range hood

must be grounded. To minimize possible

shock hazard, the cord must be plugged

into a mating, 3-prong, ground-type outlet,

grounded in accordance with National

Electrical Code, ANSI/NFPA 70 – latest

edition* and all local codes and

ordinances.

If mating outlet is not available, it is the

responsibility and obligation of the

customer to have a properly grounded, 3-

prong outlet installed by a qualified

electrician.

Do not use an extension cord.

Using a U.L.-listed power supply

cord-connection kit:

Follow Power Cord Kit instructions for

connecting wiring.

Replace terminal box cover.

19.

Turn power supply on.

Panel D

Venting through

the wall

wiring knockout

10a.

knockout behind it. Remove top or rear

wiring knockout as needed.

terminal

box

connector

blower

wiring

connector

11a.

black wires

Attach the exhaust vent connection to the

range hood. Check that the damper blade

twist-on

rotates up and down freely, if used.

connectors

12a.

Remove the screw

holding the terminal

box cover. Remove

cover.

Use two or more people to move and

install range hood.

Failure to follow this instruction can

result in back or other injury.

13a.

Lift the range hood into final position and

center. Mark on the underside of cabinet

the location of the four keyhole mounting

slots and the wiring knockout. On some

cabinets, filler blocks may need to be

added for range hood to attach to cabinet.

Set range hood aside on a protected

surface.

wall vent

knockout

wiring knockout

Remove the wall vent

knockout and the inner

damper blade

(remove if wall

cap has damper

blade)

WARNING

Excessive Weight Hazard

keyhole slot

14a.

Do Not turn on power until

installation is complete.

Run wiring through wall or cabinet

according to the National Electrical Code

and local codes and ordinances.

keyhole slot

outline

15a.

Start screws into neck area

of each of the four

keyhole mounting screw slots marked on

the cabinet bottom.

16 a.

Lift range hood into final

position, feeding electrical

wire through wiring opening. Position the

range hood so that the large end of the

keyhole slots are over the screws. Then push

the hood toward the wall so that the

screws are in the neck of the slots. Tighten

mounting screws to cabinet, making sure

mounting screws are in narrow neck of

slots. Make sure that damper blade rotates

up and down freely.

terminal box

17a .

Reinstall blower back into

position. Snap blower wire

retainer back into blower housing indents.

Reconnect the blower wiring connector

back into the terminal box connector plug.

screw