Whirlpool UXL5430BSS1 Kurulum Talimatları ve Kullanım & Bakım Kılavuzu - Sayfa 11

Havalandırma Davlumbazı Whirlpool UXL5430BSS1 için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım & Bakım Kılavuzu indirin. Whirlpool UXL5430BSS1 16 sayfaları.

Sayfayı Yazdır

4. Remove the metal grease filters from the face panel. See the

"Range Hood Care" section.

5. Attach the face panel to the hood liner. (3 sizes: The 30" x 12"

[76.2 cm x 30.5 cm] cabinet size is shown.)

See instruction below for your specific cabinet size.

A. Screws - 3.5 x 9.5 mm flat-head (4)

B. Face plate (30" x 12" [76.2 cm x 30.5 cm] shown)

C. Cabinet (30" x 12" [76.2 cm x 30.5 cm] shown)

D. Screws - 4.2 x 15 mm truss-head (2)

For cabinet size - 30" x 12" (76.2 cm x 30.5 cm)

Attach the 30" x 12" (76.2 cm x 30.5 cm) face panel (supplied

with range hood) to the hood liner using four 3.5 x 9.5 mm

flat-head screws and two 4.2 x 15 mm truss head screws.

Tighten to secure.

For cabinet size - 30" x 18" (76.2 cm x 45.7 cm)

Assemble the 30" x 6" (76.2 cm x 15.2 cm) face panel rear

extension (see the "Assistance or Service" section to order)

to the 30" x 12" (76.2 cm x 30.5 cm) face panel (supplied with

the range hood) using eight 4.2 x 8 mm screws (supplied with

the face panel rear extension).

A. Screws - 4.2 x 8 mm (8)

B. Face panel

C. Face panel rear extension

Attach the 30" x 18" (76.2 cm x 45.7 cm) face panel

assembly to the hood liner using four 3.5 x 9.5 mm flat-head

screws and two 4.2 x 15 mm truss head screws. Tighten to

secure.

For cabinet size - 36" x 18" (91.4 cm x 45.7 cm)

Attach the 36" x 18" (91.4 cm x 45.7 cm) face panel (see the

"Assistance or Service" section to order) to the hood liner

using four 3.5 x 9.5 mm flat-head screws and two 4.2 x

15 mm truss head screws. Tighten to secure.

Connect the lamp electrical connector.

Connect the Vent System

Vented Installations

1. Connect the vent system to the range hood vent opening.

Seal the connection with clamps.

Non-Vented (recirculating) Installations

1. Connect the vent system to the range hood vent opening.

Seal the connection with clamps.

2. Install vent cover.

3. Install charcoal filters. See the "Range Hood Care" section.

To order replacement kits, see the "Assistance or Service"

section.

Complete Installation

1. Replace grease filters. See the "Range Hood Care" section.

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug 3-prong power cord into a grounded 3-prong outlet

located inside the cabinet above the range hood.

3. Check the operation of the range hood fan and light. See

"Range Hood Use" section.

If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect power and check wiring connections.

NOTE: To get the most efficient use from your new range

hood, read the "Range Hood Use" section.

4. Install the cabinet doors to the cabinet. Use the assembly

instructions that come with the cabinet.