Clarion CR705R Servis Kılavuzu - Sayfa 3
Araç Alıcısı Clarion CR705R için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Clarion CR705R 20 sayfaları.
™ Audio Mode indications and Description of Operation
Audio Control
Up/Down
Audio Mode
VOL
volume
adjustment
BASS
bass
adjustment
negative indication
TREB
a
ee
treble
mio
adjustment
negative indication
BAL
left/right
balance
adjustment
FAD
front/rear
balance
adjustment
Note
1:
In the balance and fader adjustment modes, the actual steps and the steps indicated on the display do not match due to the large
number of
steps.
Note
2:
The original display reappears
approximately
5 seconds
after the adjustments in the various audio modes.
Note
3:
The various modes
are set to the following values when
the power is first turned on after the set is installed
in the car: VOL
07,
BASS 0, TREB 0, BAL 00 and FAD 00.
2. Listening to the Radio
% Band Selection Button @&
station with a weak signal, carry out the following steps.
3. Tune in the broadcasting station using Manual Tuning.
When you press button
lee eect
band changes in the following
order:
U1—>U2—>MW/LW—>U1
(U1
and U2 are on the same reception frequency band.)
XK Tuning Mode Selector Button (T-M) @
Press the button
@ so that "MAN" appears on the display. The manual
tuning mode is now set. Tune into a station by pressing button ®or
button
. Unless you press button ( or button
@ within 5 seconds
of switching to the manual tuning mode, the unit will return to the seek
tuning mode.
@ Manual Tuning
During FM reception, the frequency changes in steps of 0.05 MHz.
On MW, it changes in steps of 9 kHz, and on LW, in steps of 1 kHz.
1. Press the button
@
to set the manual tuning mode.
2. When you press button
@) , the frequency increases, and when
you press
button
, it decreases.
@
Seek Tuning (Local/DX)
There are two sensitivity levels for seek tuning: DX seek, which will
tune in any broadcasting stations which can be received, and Local
seek, where only those stations with a sufficiently strong signal,
i.e. local stations, can be tuned in.
<DX Seek>
1. Press button
@
for more than 2 seconds. "DX" appears on the
display then turns off.
2. Press button
@
to tune toward
higher frequencies and press
button
to tune toward lower frequencies. Tuning will stop
when a broadcast station is received.
<Local Seek>
1. Press button
@
for more than 2 seconds. "LO" appears on the
display then turns off.
2. Press button
@ to move to higher frequencies, button
to
move to lower frequencies. Tuning stops at a station with good
reception.
%* Preset Buttons 1,2,3,4,5and6
@
By pressing a Preset button you can instantly recall a station which has
been stored in memory.
*& When cailing a broadcasting station, unless you release the Preset
button within 2 seconds, the displayed frequency will be stored at
the Preset button, so be careful.
* Storing Stations
in the Preset Memory
6 radio stations can be stored in memory for each band.
1. Press button
to select the reception band.
2. Press button
for more than 2 seconds to store stations auto-
matically in the memory
(Auto Store). If less than 6 stations are
stored in this process, or if you want to store a broadcasting
4. Press the desired Preset button for more than 2 seconds. The
sound will go off when you press the button, and when it comes
on again, the station has been stored.
Preset Scan/Auto
Store Memory
Button @&
@
Preset Scan
Press button
. The broadcasting stations stored at Preset buttons
1 to 6 will be received in order for 5 seconds each.
When you press button
again, or press one of the Preset buttons
1 to 6, this mode will be released. (When the unit is receiving on
FM, all the stations stored in U1 and U2 will be received in order.)
* If you press button
for more than 2 seconds, the Auto Store
memory mode will become operative.
All the stations stored in
the memory so far will be cleared, and new ones willbe stored
instead, so be careful.
@
Auto Store
Memory
6 strong-signal broadcasting stations can be stored automatically
for each band. (See "Storing Stations in the Preset Memory".)
¥%& Stations previously stored in the preset memory are cleared
when
new ones are Stored using Auto Store.
3& Stereo Reception indicator
When a stereo broadcast is received, the "ST" indicator
© tights up.
3. RDS(Radio
Data System) Operation
% RDS Button &
Set the RDS mode by pressing the button
@ , so the "RDS"
indicator
@ lights up When you press the button again, this mode is released.
1, When an RDS station is received, the programme name is displayed.
(PS:Programme
Service Name)
2. If an emergency broadcast is received while an RDS station is being
received
, "ALARM"
is displayed.The volume of the emergency
broadcast is automatically set at the pre-set value.
3. If good reception of the RDS broadcast becomes impossible in your
present location, the "RDS" indicator
@) starts blinking.
4. When seek tuning is carried out in the RDS mode, only stations
broadcasting an RDS signal will be received.
5. @
Preset Scan in RDS Mode
When you press the button
, Preset Scan will be carried out
only on the RDS stations among
the preset stations.
@
Auto Store in RDS
Mode
When you press the button
for more than 2 seconds, only
RDS stations will be stored on the Preset buttons.
* Same-Programme
Search
-3-
ARB4171R CR705R