Xerox 6180DN - Phaser Color Laser Printer Manuel - Sayfa 18

Yazıcı Xerox 6180DN - Phaser Color Laser Printer için çevrimiçi göz atın veya pdf Manuel indirin. Xerox 6180DN - Phaser Color Laser Printer 28 sayfaları. 26-ppm monochrome/ 20-ppm color
Ayrıca Xerox 6180DN - Phaser Color Laser Printer için: Kurulum Kılavuzu (34 sayfalar), Şartname Sayfası (2 sayfalar), Kullanıcı Kılavuzu (32 sayfalar), Kullanıcı Kılavuzu (28 sayfalar), Kurulum Kılavuzu (2 sayfalar), Güvenlik Kılavuzu (38 sayfalar), Yayın Notu (2 sayfalar), Kurulum Kılavuzu (2 sayfalar), Başlangıç Kılavuzu (37 sayfalar), Manuel (34 sayfalar), Manuel (34 sayfalar), Başlangıç Kılavuzu (34 sayfalar), Kullanıcı Kılavuzu (32 sayfalar), Kurulum ve Kullanım Kılavuzu (8 sayfalar), Teknik Özellikler (4 sayfalar)

Sayfayı Yazdır
Xerox 6180DN - Phaser Color Laser Printer Manuel
Paper Handling
PAPER OUTPUT AND FINISHING
Office workgroup devices' paper-output handling options
range from duplex printing to saddle-stitch booklet making.
Many devices offer a choice of finisher/staplers, which
provide a low-cost, minimum footprint solution, or a high-
capacity, fully featured solution such as multi-position
stapling, saddle-stitch booklet maker and/or document
hole puncher.
BERTL evaluates these functions looking at how the same
job outputs at different speeds when different finishing
options are specified. The impact of the finishing selection
is determined by timing jobs that are sent to a device with
various finishing settings.
Stapling
Lower-cost finisher/stapler units often have a 15- to 30-
sheet maximum stapling capability and are often limited to
corner stapling. Floor-standing, higher-cost finishers
typically provide 50-sheet capability and provide both
corner and double stapling.
Saddle-stitch booklet making allows users to create
folded,
center-stapled
booklets.
finishers only handle 10 sheets (for producing 40-page
booklets), with others handling up to 15 sheets (for
producing 60-page booklets).
Mail Bin Units and Offset Output
Many workgroup devices provide offset stacking (each set
is offset from the next) to make it easier to separate jobs.
Some also provide physical mail bin units that allow each
user to send jobs to their own tray. However, most mail-
bin units do not accept finished (such as stapled) jobs. A
multi-tray finisher can also offer some form of job
separation typically used to separate different types of
jobs (fax, print, copy) for easier identification.
Post-Process Insertion (PPI)
A post-process insertion unit can be used to automatically
insert pages into completed print jobs. These inserts can
include chapter covers, color pages and specialty
material, such as heat-sensitive materials that may
damaged if run through the device. The advantage of
course is that no human intervention is required to
manually insert pages into completed jobs.
Copyright © 2007 MCA Internet, LLC dba BERTL.
All Rights Reserved. The license under which this document is made available and applicable law prohibit any reproduction or further transmission of any portion of this document. This
document may only be viewed electronically through the www.BERTL.com Web site and may not be stored in electronic or hard copy format. Any reproduction of trademarks is strictly
prohibited. BERTL accepts no responsibility for any inaccuracies or omissions contained in this document.
Some
saddle-stitch

Output/Finishing Features Summary

Standard Output Tray Capacity
Optional Output Option(s)
Optional Output Tray Capacity
Maximum Stapling Capacity
Maximum Stacking Capacity
Maximum Saddle-Stitch Capacity
Hole-Punch Option(s)
Physical Mail Bin Option(s)
Folding Option(s)
Post Process Inserter Option(s)
PPI Capacity
The Xerox Phaser 6180 can print on covers, separator pages,
transparencies, and envelopes as shown on the photos below.
May 2007
Xerox Phaser 6180DN
300 sheets
No
No
N/A
300 sheets
N/A
No
No
No
No
N/A
May. 18, 07
Page 18