Calex PYROPEN R Manuel - Sayfa 2

Termometre Calex PYROPEN R için çevrimiçi göz atın veya pdf Manuel indirin. Calex PYROPEN R 20 sayfaları. Handheld infrared thermometer

Sayfayı Yazdır

DISPLAY

A Main temperature

reading

B Scan indicator

C Hold indicator

D Celcius or Fahrenheit

indicator

E Low battery indicator

F Max/Min/Average

temperature

G Laser Indicator

H Emissivity indicator

AFFICHAGE

A Indication de

température

principale

B Indicateur Scan

C Indicateur Hold

D Indicateur Celsius ou

Fahrenheit

E Indicateur de charge

de la pile

F Température

Max/Min/Moyenne

G Indicateur Laser

H Indicateur

d'émissivité

DISPLAY-ANZEIGE

A Temperaturanzeige

B Anzeige Scan

C Anzeige Hold

D Anzeige Celsius oder

Fahrenheit

E Anzeige

Batteriezustand

SCAN

SCANSIONE

(A)

MODE DISPLAY CODES

CODES D'AFFICHAGE DES MODES

MODUS-ANZEIGECODES

CÓDIGOS DE FUNCIÓN

CODICI DI DISPLAY DEL MODO

SCAN

MAX

MIN

F Max/Min/Average

Temperaturanzeige

G Laseranzeige

H Emissionsanzeige

PANTALLA

A Lectura principal de

temperatura

B Indicador SCAN

(medición)

C Indicador HOLD

(espera)

D Indicador de grados

Celsios o Fahrenheit

E Indicador de pila

baja

F Temperatura

Max/Min/Med

G Indicador láser

H Indicador de

emisividad

DISPLAY

A Lettura temperatura

principale

B Indicatore scan

C Indicatore hold

D Indicatore Celsius o

Fahrenheit

E Indicatore basso

livello batteria

F Temperatura

Max/Min/Media

G Indicatore Laser

H Indicatore Radianza

°C/°F (B)

163mm

MODE

MODO

(C)

AVG

OPERATION

To take a temperature reading, point the unit at the

object you wish to measure. Press the SCAN button

(A) and read the temperature on the unit's LCD,

"SCAN" will appear on the display while the unit is

actively taking a temperature, "HOLD" when the

unit is displaying the last recorded temperature. The

unit will hold the last reading for 10 seconds after the

button is released.

To change between Celsius and Fahrenheit, press

button (A) then press the °C/°F button (B) until the

change occurs on the display.

The Pyropen also measures Maximum (MAX),

Minimum (MIN) and Average (AVG) temperatures

each time you take a reading. This data is stored and

can be recalled until new measurements are taken.

To recall stored values. With the unit in HOLD, press

the MODE button (C). Each time you press the MODE

button, you advance through the MODE cycle.

To select MAX, MIN and AVG, press button (A), then

press the MODE button (C) until the appropriate code

appears.

If the object you wish to measure is highly reflective,

you may need to lower the emissivity setting of the

Pyropen. NOTE: Most materials have high emissivities

(paper, plastics, rubber, painted or oxidised metals)

and it will not be necessary to alter the factory-set

emissivity value of 0.95.

To change the emissivity. With the unit in HOLD, press

the MODE button (C) until the

Press button (A) (

(B) and (C) to lower or raise the emissivity. When the

emissivity is correct, press button (A) to complete the

operation.

To ensure accurate aiming of the Pyropen, laser sighting

is fitted. When aiming at a target, the red dot of the

laser will be approximately 1cm to the right of the cen-

tre of the spot being measured.

To enable laser sighting. Press button (A), then press

the MODE button (C) until the laser symbol (

es. Press button (B) to enable or disable laser sighting

(display reads ON or OFF accordingly). Press button

sons the laser is activated ONLY when SCAN button

(A) is pressed.

WARNING: Laser radiation may be harmful to the

human eye.

Avoid direct exposure of human eyes to laser light.

Avoid indirect exposure via reflective surfaces such as

glass and mirrors. Never aim the unit at another per-

son. Laser will not operate in ambient temperatures

above 40°C

The Pyropen can be locked into the SCAN mode with-

out the need to continually press button (A). To lock

the unit into the SCAN mode: With the unit in HOLD

mode, press buttons (B) and (C) simultaneously until

"LOCK" appears in the LCD. To switch the Pyropen off

press button (A) twice.

FONCTIONNEMENT

Pour relever une température, pointer l'unité vers l'ob-

jet dont la température doit être mesurée. Appuyer sur

le bouton 'SCAN' (A) et lire la température sur l'af-

fichage à cristaux liquides de l'unité, 'SCAN' apparaît sur

l'écran pendant que l'unité prend la température active-

ment, 'HOLD' lorsque l'unité affiche la dernière tem-

pérature enregistrée. L'unité affiche le dernier relevé

pendant 10 secondes après que le bouton a été relâché.

Pour passer de Celsius en Fahrenheit et vice versa,

appuyer sur le bouton (A), puis appuyer sur le bouton

°C/°F (B) jusqu'à ce que le changement apparaisse sur

l'affichage.

Le Pyropen mesure également les températures

Maximum (MAX), Minimum (MIN) et Moyennes

(AVG) à chaque fois qu'un relevé est effectué. Cette

donnée peut être mémorisée et rappelée jusqu'à ce

que de nouvelles mesures soient prises.

Pour rappeler des valeurs mémorisées. L'unité doit être

en mode 'HOLD' et appuyer sur le bouton 'MODE' (C).

Chaque fois que le bouton 'MODE' est appuyé, le cycle

de 'MODE' progresse.

symbol is displayed.

symbol flashes) then use buttons

) flash-