Yamaha DTX520K Kullanıcı El Kitabı - Sayfa 36
Müzik Enstrümanı Yamaha DTX520K için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Yamaha DTX520K 48 sayfaları. Dtx drums
Ayrıca Yamaha DTX520K için: Montaj Kılavuzu (2 sayfalar), Montaj Kılavuzu (2 sayfalar)
Sayfayı Yazdır
8 Trigger Setup Edit
DT LoTom DT series drum trigger (for a large toms)
DT Kick
DT series drum trigger (for a bass drum)
misc~1–6 Other manufacturer's pads 1 to 6
*1 These pad types are different in the sensitivity settings among
the three sections (the Bow section, Edge section, and Cup
section in 3-zone cymbal pad.) You can change these as
desired.
"CY-1" is the setting that the sensitivities of the three sections
are same.
"CY-2" is the setting that the sensitivity of the Edge section is
set fairly lower than the other section.
"CY-3" is the setting that the sensitivity of the Cup section is
set fairly lower than the other section.
TRG3
Gain, MVI (Minimum Velocity)
TRG3~
ƒsnare~~0%
"Gain=65MVl=~12‚
Gain
[Range]
0–99
Adjusts the input gain (sensitivity) for the input jack assigned in
the upper half of the page.
Setting a larger value lets a smaller input level from the pad cre-
ate sound.
* This value will be automatically set after the appropriate pad
type is set in [TRG2 Type (Pad Type)]. Some fine-tuning of the
value will be necessary.
* Some pads are equipped with a sensitivity adjustment knob.
For details, refer to the owner's manual that came with the
particular pad.
MVI
[Range]
1–127
Sets the MIDI Velocity (volume) that is transmitted when the pad
is hit the softest. Large values will produce a high volume level
even if the pad is hit softly. However, this will result in a narrow
volume range making it difficult to adequately produce wider
dynamic levels.
The Trigger Input Level will be displayed in percentage in the
upper right hand corner of the display. The maximum velocity
(input level 99 percent) will be 127. The lower the level is when
the pad is hit the weakest, the wider the potential dynamic range
will be.
* This value is automatically set after the appropriate pad type
is set in [TRG2 Type (Pad Type)]. Some fine-tuning of the
value will be necessary.
36
DTX500 Owner's Manual
TRG4
VelCurve (Velocity Curve)
TRG4~
ƒsnare~~0%
"VelCurve=norm~‚
Sets the Input Velocity Curve for the input jack assigned in the
upper half of the page.
norm
loud2
loud1
Strength of hit →
TRG5
RejTime (Self Rejection Time)
TRG5 ~ƒsnare~~0%
"~~RejTime=1~~~‚
[Range]
0–9
Prevents double triggering from occurring in the input jack
assigned in the upper half of the page. After an event is detected,
further events will be automatically muted for a certain length of
time. The larger the value, the longer time events will be muted.
TRG6
RejLvlAll (Rejection Level)
TRG6 ~ƒsnare~~0%
"~RejLvlAll=2~~‚
[Range]
0–9
Prevents crosstalk from occurring in the input jack assigned in
the upper half of the page. Events triggered by other pads (input
jacks) that are of a lower input value than what is set here will not
be triggered for a certain length of time. Larger values require a
greater input level in order to produce a trigger event.
hard1
hard2