Yamaha YDP-101E Kullanıcı El Kitabı - Sayfa 37

Müzik Enstrümanı Yamaha YDP-101E için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Yamaha YDP-101E 48 sayfaları. Yamaha digital piano owner's manual

Sayfayı Yazdır

(2)

Universal Non-Realtime Message (GM On)

General MIDI Mode On

Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->

[F7H]

F0H

= Exclusive status

7EH

= Universal Non-Realtime

7FH

= ID of target device

09H

= Sub-ID #1=General MIDI Message

01H

= Sub-ID #2=General MIDI On

F7H

= End of Exclusive

F0H

= Exclusive status

7EH

= Universal Non-Realtime

XnH

= When received, n=0~F.

X = don't care

09H

= Sub-ID #1=General MIDI Message

01H

= Sub-ID #2=General MIDI On

F7H

= End of Exclusive

When the General MIDI mode ON message is received, the MIDI

system will be reset to its default settings.

This message requires approximately 50ms to execute, so suffi-

cient time should be allowed before the next message is sent.

8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1)

XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

[mmH] -> [ll H] -> [ddH] -> [F7H]

F0H

= Exclusive status

43H

= YAMAHA ID

1nH

= When received, n=0~F.

When transmitted, n=0.

4CH

= Model ID of XG

hhH

= Address High

mmH

= Address Mid

ll H

= Address Low

ddH

= Data

F7H

= End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI system

will be reset to its default settings.

The message requires approximately 50ms to execute, so suffi-

cient time should be allowed before the next message is sent.

(2)

XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

[bbH] -> [hhH] -> [mmH] -> [ll H] ->

[ddH] ->...-> [ccH] -> [F7H]

F0H

Exclusive status

43H

YAMAHA ID

0nH

When received, n=0~F.

When transmitted, n=0.

4CH

Model ID of XG

aaH

ByteCount

bbH

ByteCount

hhH

Address High

mmH

Address Mid

ll H

Address Low

ddH

Data

ccH

Check sum

F7H

End of Exclusive

• Receipt of the XG SYSTEM ON message causes reinitialization

of relevant parameters and Control Change values. Allow suffi-

cient time for processing to execute (about 50 msec) before

sending the YDP-101 another message.

• XG Native Parameter Change message may contain two or four

bytes of parameter data (depending on the parameter size).

• For information about the Address and Byte Count values, refer

to Table 1 below. Note that the table's Total Size value gives the

size of a bulk block. Only the top address of the block (00H, 00H,

00H) is valid as a bulk data address.

9. SYSTEM EXCLUSIVE MESSAGES

(YDP-101 MIDI Format)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] ->

[F7H]

F0H

= Exclusive status

43H

= Yamaha ID

73H

= YDP ID

5FH

= Product ID

nnH

= Substatus

Control

02H

Internal MIDI clock

03H

External MIDI clock

06H

Bulk Data (the bulk data follows 06H)

F7H

= End of Exclusive

* When nn=02H or 03H, YDP common ID (01H) is recog-

nized as well as 5FH.

BULK DUMP FORMAT

F0H, 43H, 73H

5FH

06H

05H

0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH =Data length

[BULK DATA]

[CHECK SUM (1byte)] = 0-sum (BULK DATA)

F7H

10. SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->

[0nH] -> [ccH] -> [vvH] -> [F7H]

F0H

= Exclusive status

43H

= Yamaha ID

73H

= YDP ID

5FH

= Product ID

11H

= Special control

0nH

= Control MIDI change (n=channel number)

= Control number

= Value

F7H

= End of Exclusive

Control

Metronome

Always 00H

Channel Detune

ch: 00H-0FH

Voice Reserve

ch: 00H-0FH

* When Volume, Expression is received for Reserve On, they will

be effective from the next Key On. Reserve Off is normal.

11. SYSTEM EXCLUSIVE MESSAGES (Others)

Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->

[00H] -> [00H] -> [mmH] -> [ll H] -> [ccH] ->

[F7H]

Master Tuning (XG and last message priority) simultaneously

changes the pitch of all channels.

F0H

= Exclusive Status

43H

= Yamaha ID

1nH

= Transmission from n=YDP-101 is always 0.

0-F is received.

27H

= Model ID of TG100

30H

= Sub ID

00H

mmH

= Master Tune MSB

ll H

= Master Tune LSB

ccH

= don't care (under 7FH)

F7H

= End of Exclusive

=Product ID

=Bulk ID

=Sequence data

= End of Exclusive

ccH

vvH

1BH

00H : off

01H : –

02H : 2/4

03H : 3/4

04H : 4/4

06H : 6/4

7FH : No accent

43H (Sets the Detune value for

each channel)

00H-7FH

45H

00H : Reserve off

7FH : on*

YDP-101