Yamaha HTR-5930 Sistem Bağlantı Kılavuzu

Alıcı Yamaha HTR-5930 için çevrimiçi göz atın veya pdf Sistem Bağlantı Kılavuzu indirin. Yamaha HTR-5930 1 sayfaları. Digital home theater system
Ayrıca Yamaha HTR-5930 için: Şartname (2 sayfalar)

Sayfayı Yazdır
Yamaha HTR-5930 Sistem Bağlantı Kılavuzu
© 2006
Printed in China
YHT -270
DIGITAL HOME THEATER SYSTEM
SYSTEM CONNECTION GUIDE
Thank you for selecting this YAMAHA YHT-270.
1
About This system
Front speakers (NX-E270) 1
Center speaker (NX-C270) 2
Subwoofer (SW-P270) 4
Surround speakers (NX-E270) 3
Receiver (HTR-5930)
Supplied accessories
For NS-E270 / NS-C270
For SW-P270
For HTR-5930
Speaker cable
Speaker cable
AM loop antenna
Subwoofer cable
4 m (157-1/2") x 3
10 m (393-11/16") x 2
4 m (157-1/2") x 1
for Center/Front
for Surround
speakers
speakers
Indoor FM antenna
Remote control, Batteries (AA,
Non-skid pad
Non-skid pad
R06, UM-3) x 2 and Owner's
Fastener x 2 set
4 pcs x 1 set
manual are also included, but
8 pcs x 2 set
for NS-C270
For NS-E270
not shown.
Major specifications for speakers
(HTR-5930: refer to the "HTR-5930 Owner's manual" for specifications and safety cautions.)
NX-E270
NX-C270
SW-P270
acoustic-suspension
acoustic-suspension
Advanced YAMAHA
Type
speaker system,
speaker system,
Active Servo Technology,
Magnetically shielded type
Magnetically shielded type
Magnetically shielded type
Power
Maximum: 80 W
Maximum: 100 W
Dynamic power: 100 W
Frequency response
100 Hz - 25 kHz
130 Hz - 20 kHz
30 Hz - 200 Hz
105 x 151 x 113 mm
300 x 72 x 113 mm
200 x 365 x 370 mm
Dimension
(W x H x D)
(4-1/8" x 5-15/16" x 4-7/16")
(11-13/16" x 2-27/32" x 4-7/16")
(7-7/8" x 14-3/8" x 14-9/16")
0.9 kg (1.98 lbs)
8.5 kg (18.74 lbs)
Weight
0.8 kg (1.76 lbs)
2
About speakers
Before making connections, place all speakers in their respective positions. The positioning of the
speakers is important because it controls the whole sound quality of your audio system.
Place the speakers depending on your listening position by following the instructions below.
Carrying most of the music/sound effects.
1
Front speakers
Place them on both sides of your TV set. Approximately at the same height as the TV set.
Emitting center sound such as dialog.
2
Place it precisely between the front speakers. You can place the center speaker on top of the TV if the top
Center speaker
is flat, on the floor under the TV, or inside the TV rack. Be sure to place the speaker in a stable position.
Providing the surround/ambient effects.
3
Surround speakers
Place them behind your listening position, facing slightly inward. About 1.8 m (approx. 6 feet) from the
floor.
Adding the low-frequency bass sound.
4
Subwoofer
As a recommended positioning of the subwoofer, place the subwoofer on the outside of either the right or
the left front speaker. For more detail, read "3 Placing the speakers - Subwoofer".
Speaker layout
1
4
Front R
Subwoofer
Front L
2
Surround R
Center
3
Surround L
All rights reserved.
3
WG84200
Placing the speakers
UC
Center speaker
When placing the speaker on top of the TV rack, etc., attach
the provided fasteners at two points on the bottom of the
speaker and on the top of the TV.
Peel off
the seal
Notes
• Do not place the center speaker on top of a TV whose area is
smaller than the bottom of the speaker. If placed, the speaker
may fall and cause injury.
• Do not place the center speaker on top of a TV if the top is
inclined.
• Do not touch the adhesive surface after peeling off the seal, as
this will waken its adhesive strength.
• Thoroughly wipe clean the surface where the fastener is to be
applied. Note that adhesive strength is weakened if the surface is
dirty, oily or wet and that this may cause the center speaker to
fall.
Front and surround speakers
Placing the speakers
When placing the speakers on a flat surface,
attach the included non-skid pads to the corner on
the bottom of the speakers. This prevents the
speakers from sliding.
Mounting the speakers on the wall
You can mount the front and/or surround speakers on a wall. To mount them on a wall, use the holes of the
brackets attached on the back panels of the speakers.
2
1
Fasten two screws into a firm wall or wall support at
Hang the speaker by mounting the holes on the
protruding screws.
the interval shown below.
Make sure that the screws are securely affixed by the
narrow parts of the holes.
70 mm
(2-3/4")
70 mm
Holes
(2-3/4")
70 mm
(2-3/4")
10 mm
(2-3/4")
Minimum
20 mm (25/32")
Caution
• Each speaker weighs 0.8 kg (1.76 lbs).
• Do not mount the speakers on thin plywood or a wall composed of a soft surface material. If mounted, the
screws may pull out of the flimsy surface and the speakers may fall. This may damage the speakers or cause
personal injury.
• Do not affix the speakers to a wall using nails, adhesives, or any other unstable hardware. Long-term use and
vibrations may cause the speakers to fall.
• To avoid accidents resulting from tripping over loose speaker cables, fix the cables to the wall.
• Select an appropriate position on the wall to mount the speaker so that no one will injure his/her head or face.
Installing the speakers on commercially available speaker stands
When you install the speakers on commercially
*Please use the speaker stand that fits with this size.
available speaker stands, you need to attach the
brackets (option) to the bottom of the speakers using
screws (option).
60 mm (2-3/8")
Subwoofer
It is recommended to place the subwoofer on the outside
Use the non-skid pads
of either the right or the left front speaker (figure A). The
placement shown in figure B is also possible, however, if
Attach the provided non-skid pads at the four corners on
the subwoofer is placed directly facing the wall, the bass
the bottom of the subwoofer to prevent the subwoofer
sound may lessen because the sound from the subwoofer
from moving by vibrations, etc.
and the sound reflected by the wall may cancel out each
other. To prevent this from happening, face the subwoofer
obliquely to the wall.
A
B
: Subwoofer
: Front speaker
4
Connecting speakers and antennas to the receiver
CAUTION
Plug the power cables for the AV receiver
and other audio/video components into an
AC outlet only after you complete all other
connections.
Keep the speaker cables as short as
possible. Do not bundle or roll up excess
cable. If the connections are faulty, you will
hear no sound from the speakers.
Before connecting
• Cut the supplied speaker cable to the appropriate
length as required.
• Remove the insulation coating at extremity of each
speaker cable by twisting the coating off.
Notes
• Do not let uninsulated bare wires touch each other as this
could damage the speaker or the amplifier.
• Securely twist the bare wires and lump them together to
prevent them causing a short circuit.
Good
Not Good
10 mm
(3/8")
Non-skid pad
4 4 4 4 4
5
Connecting other components to the receiver
This procedure introduces an example of digital and
analog connections. For information about other
connection methods, refer to the "HTR-5930
Owner's Manual".
CAUTION
Plug the power cables for the AV receiver
and other audio/video components into an
AC outlet only after you complete all other
connections.
Information on jacks
and cable plugs
Audio jacks and cable plugs
Insert only M4
screws through the
AUDIO
DIGITAL AUDIO
DIGITAL AUDIO
outside holes.
R
L
COAXIAL
OPTICAL
(red)
(white)
(orange)
Bracket (AAX34790)
(option)
R
L
C
O
DIGITAL
DVD
Screw (AAX12390)
(option)
Left and right
Optical digital
Coaxial digital
analog audio
COAXIAL
audio cable
audio cable
OPTICAL
cable plugs
plug
plug
DTV-CBL
DVD
Video jacks and cable plugs
COMPONENT VIDEO
VIDEO
Y
P
B
P
R
(green)
(blue)
(red)
(yellow)
V
Y
P
P
B
R
Composite video
Component video
cable plug
cable plug
(U.S.A. model only)
XM Connect-and-
4 4 4 4 4
Play digital antenna
Connect the XM Connect-and-Play digital
antenna accessory (sold separately) to the
XM jack.
1 1 1 1 1
Surround speakers
Right
2 2 2 2 2
Left
Connecting to the
Antennas
receiver terminals of
the Antennas
Locate AM loop antenna and
indoor FM antenna, and connect to
the receiver. For more details, refer
to the "HTR-5930 Owner's
Manual".
XM
MULTI CH INPUT
AUDIO
VIDEO
COMPONENT VIDEO
TUNER
R
L
Y
P
B
P
R
DVD
FRONT
DVD
A
AM
DTV/
ANT
CBL
DTV/
SURROUND
B
CBL
GND
DIGITAL
INPUT
SUB
CENTER
3
WOOFER
VCR
FM
DVD
V-AUX
C
ANT
COAXIAL
IN
CD
OPTICAL
2
DTV-CBL
VCR
MONITOR OUT
IN
(PLAY)
OUT
R
SURROUND
L
CENTER
MD/
DVD
CD-R
1
OUT
SUB
(REC)
WOOFER
MONITOR
R
L
OUT
AUDIO
OUTPUT
Subwoofer
cable
Connecting to the speaker or the receiver terminals
1
Press and hold the terminal tab, as shown in the figure below.
2
Insert the bare wire core.
3
Release your finger from the tab to allow it to lock securely on the bare wire core.
4
Test the security of the connection by pulling gently on the cable at the terminal.
Speaker terminals
red (+)
black (-)
Note:
Do not insert the
insulation coating into
the hole. The sound may
2
not be produced.
1
Subwoofer
To AC outlet
1 1 1 1 1
2 2 2 2 2
Cable TV or satellite tuner
DVD player
1. Connect the component video output jacks of your cable TV
1. Connect the component video output jacks of your DVD
or satellite tuner to the COMPONENT VIDEO (DTV/CBL)
player to the COMPONENT VIDEO (DVD) jacks of this
jacks of this unit using a component video cable.
unit using a component video cable.
2. Connect the optical digital audio output jack of your cable
2. Connect to the optical digital audio signal output jack of
TV or satellite tuner to the DIGITAL INPUT (DTV/CBL)
your DVD player to DIGITAL INPUT (DVD,COAXIAL)
jack of this unit using an optical digital audio cable.
jack using an optical digital audio cable.
P
R
O
P
C
B
Video out
Y
Digital out (optical)
Digital out
(Component)
(coaxial)
XM
MULTI CH INPUT
AUDIO
VIDEO
COMPONENT VIDEO
TUNER
R
L
Y
P
B
P
R
DVD
FRONT
A
DVD
AM
DTV/
ANT
CBL
SURROUND
DTV/
B
GND
CBL
INPUT
SUB
CENTER
3
WOOFER
VCR
V-AUX
C
FM
ANT
CD
IN
B
2
VCR
MONITOR OUT
FRONT
IN
R
L
R
SURROUND
L
CENTER
(PLAY)
OUT
MD/
CD-R
1
OUT
SUB
(REC)
WOOFER
MONITOR
OUT
R
L
AUDIO
OUTPUT
Audio in
Audio out
Audio in
Audio out
L
L
L
L
R
R
R
R
6 6 6 6 6
CD recorder or MD
5 5 5 5 5
DVD recorder or VCR
recorder
1. Connect the component video output jacks of your DVD recorder or
Connect the analog audio output jacks of your CD recorder
VCR to the COMPONENT VIDEO (VCR) jacks of this unit using a
or MD recorder to the MD/CD-R IN (PLAY) jacks on this
component video cable.
unit using an analog audio cable (stereo).
2. Connect the analog audio output jacks of your DVD recorder or VCR to
y To record audio sources output at the MD/CD-R OUT
the AUDIO VCR IN jacks on this unit using an analog audio cable.
(REC) jacks, you need to connect the source component
y To record audio and video sources output at the VCR OUT jacks, you
using an analog connection. For details, refer to the
need to connect the source component using an analog connection. For
"HTR-5930 Owner's Manual".
details, refer to the "HTR-5930 Owner's Manual".
3 3 3 3 3
Front speakers
Connecting to the
Left
Right
receiver terminals of
the front speakers
1
Loosen the knob.
2
Insert the bare wire core of the
speaker cable into the hole on
the terminal.
3
Tighten the knob to secure the
wire.
2
1
3
HTR-5930
IMPEDANCE SELECTOR
SPEAKERS
A
CLASS 2 WIRING
R
FRONT
L
B
FRONT
R
L
red (+)
Receiver terminals
2
1
5 5 5 5 5
black (-)
Center speaker
3 3 3 3 3
Video monitor
Connect the component video input jacks of video
monitor to the COMPONENT VIDEO (MONITOR
OUT) jacks of this unit using a component video
cable.
Video in
(Component)
P
P
R
R
P
P
B
B
Y
Y
Video out
(Component)
HTR-5930
IMPEDANCE SELECTOR
SPEAKERS
A
CLASS 2 WIRING
R
FRONT
L
Video out (Component)
Video in
P
R
V
P
B
Y
7 7 7 7 7
Plug in the power
After you complete all cable connections,
plug in the receiver, subwoofer, DVD player
and other components to the AC outlet.