Yamaha MA2030 Kullanıcı El Kitabı

Amplifikatör Yamaha MA2030 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Yamaha MA2030 2 sayfaları. Yamaha power amplifiers technical specifications
Ayrıca Yamaha MA2030 için: Kullanıcı El Kitabı (5 sayfalar), Teknik Özellikler (2 sayfalar)

Sayfayı Yazdır

ZJ24810

POWER AMPLIFIER

Owner's Manual

First, please carefully read the "IMPORTANT SAFETY INSTRUCTIONS" on the reverse side.

Thank you for your purchase of the Yamaha MA2030/PA2030 power amplifier. Please read through this

manual carefully before beginning use, so that you will be able to take full advantage of the device's

various functions. After you have read the manual, keep it in a safe place.

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat

different from those on your device.

• The company names and product names in this manual are the trademarks or registered trademarks of

their respective companies.

• In this manual, the

mark indicates content that is unique to the MA2030, and

content unique to the PA2030. Contents that are common to both have no marks.

• Amplifier illustrations are mainly from the MA2030. Where necessary, illustrations of the PA2030 are also

shown.

Features

• Supports both kinds of speaker connection: high-impedance connection and low-impedance

connection.

• Equipped with digital processor (Feedback Suppressor, Ducker, Leveler).

• Optional PA2030 expansion amplifier enables connection of additional speakers.

Included items (please check)

• Power cord (2.0m)

• Euroblock plugs (3-pin, 3.50mm pitch) x 1

, x 2

• Technical Specifications (English only): includes block diagram, dimensions, and input/output

specifications.

• Owner's Manual (this sheet)

Setup

Step

Option

Speakers

Step

Front panel

Portable audio player,

Option

etc.

Step

Control Panel

Rear panel

CD players, tuners, etc.

Step

Option

To AC outlet

Step

Speaker expansion

Volume adjustment

Connecting Speakers

Step

Change the setting depending on the speaker connection (high- or low-impedance connection), the kind

of speakers, and the installation location of the speakers. Refer to "Connecting Speaker Cables" at the

right bottom on this page and the explanation of high-impedance connection, etc. at the following URL.

Yamaha Pro Audio site: "Better Sound for Commercial Installations":

http://www.yamahaproaudio.com/global/en/training_support/better_sound/

Caution

• Before connecting speakers, make sure that the power of the device is turned off. If the power is on, there is a risk of

electrical shock.

• Ensure that load is not applied to the speaker cable.

• In a high-impedance installation, make sure that the sum of the power input ratings of the speakers to be connected

does not exceed 60W.

• In a low-impedance installation, make sure that the total impedance of speakers to be connected is at least 3 ohms.

■

High-impedance Connections (60W x 1 channel)

Maximum output

voltage: 100V

voltage: 70V

Set the speaker output to high-impedance by setting the [OUTPUT] switch to

[100V] or [70V] corresponding to the maximum output voltage.

Use speaker cables to connect the [SPEAKERS A]

terminal to the positive "+"

terminals of the speakers, and the [SPEAKERS B]

terminal to the negative "-"

terminals.

In case of high-impedance connection, the [SPEAKERS A]

and [SPEAKERS B]

not used. Do not connect to the terminals.

Note

The speaker output is processed through a high pass filter (80Hz, 18dB/oct.).

■

Low-impedance Connections (30W x 2 channels)

Speaker impedance

Set the speaker output to low-impedance connection by setting the [OUTPUT] switch

to [4Ω 3Ω].

Set the [SETUP] DIP switch 1 to [4Ω] (up, impedance: 4Ω or more) or [3Ω] (down,

impedance: 3Ω to 4Ω) corresponding to the specifications of the speakers to be

connected.

Connect the [SPEAKERS A]

terminals to the "+"/"-" terminals of the first

speaker, and the [SPEAKERS B]

terminals to the "+"/"-" terminals of the second

speaker.

indicates

■

Configuration of Speaker Output Signal

Connecting Yamaha Speakers

Setting mono/stereo output

[SETUP] DIP switch 4/5

[SETUP] DIP switch 7

Setting the [SETUP] DIP switches optimizes the

In a low-impedance installation, if speakers are

output signal to match Yamaha speakers designed

placed in a stereo arrangement, set to stereo

for commercial installations.

output.

[SETUP] DIP switch

Surface

High-impedance

Yamaha speakers

down

mount-type

connections

designed for

commercial installations

Ceiling-type down

down

Low-impedance

connections

Non-Yamaha speakers

—

—: Setting is not required. (Either up or down can be used.)

*1: When stereo audio is output, the left channel signal

is output from the [SPEAKERS A] terminals and the

right channel signal is output from the [SPEAKERS B]

terminals.

Connecting External Devices

Step

RCA type

mini-stereo

type

Microphones

MA2030 front panel

MA2030 rear panel

Connect a BGM (background music) tuner, a CD player, a portable audio player, etc. to the stereo input jacks

(DCP1V4S)

of this device.

Jack position

Jack name

Front panel

[ST IN 1] jack

mini-stereo type (unbalanced input)

MA2030

[ST IN 2] jack

Rear panel

RCA type (unbalanced input)

[ST IN 3] jack

Euroblock connector (balanced input; connect with supplied

PA2030

Rear panel

[LINE IN] jack

Euroblock plugs), RCA type (unbalanced input)

Note

Refer to "Attaching Euroblock Plugs" for Euroblock plug installation.

Make sure that this device and all devices to be connected are turned off.

Connect this device and any external devices with appropriate cables.

Leveler (suppressing wide playback volume variations)

[SETUP] DIP switch 6

The Leveler function automatically suppresses and corrects for large changes

in the playback volume from external devices for a more consistent sound,

such as when reproducing BGM (background music).

Connecting Power Cord and Turning On

Step

AC IN connector

MA2030 front panel

MA2030 rear panel

Make sure power switches of this device and devices connected to this device are

turned off (in

position).

Turn the [VOLUME] knob all the way to the left.

Connect the supplied power cord to the AC IN connector.

Insert the power cord plug into an appropriate outlet.

After turning on the connected devices (portable audio players, CD players, etc.), turn

on this device.

Note

• Before turning on the power, please check that there are no problems with the cabling, connections, and so on.

• When turning the system off, turn off this device, and then connected devices.

terminals are

Adjusting Volume

Step

[SETUP] DIP switch

4Ω or more

MA2030 front panel

3Ω to 4Ω

down

Select a stereo input by rotating the [ST SOURCE] knob.

The [ST SOURCE] indicator corresponding to the selected input signal lights.

Input audio signal from the external device, and confirm that sound is being output

from the speakers by gradually rotating the [VOLUME] knob to the right.

Make sure that the [VOLUME SIGNAL] indicator lights according to the sound input and that sound

comes from the speakers.

Matching the volume levels of external devices

When connecting two or more external devices, you can lower the volume of the louder devices to match the

level of the faintest device.

Select the stereo input with the loudest sound by rotating the [ST SOURCE] knob.

Press and hold the [ST SOURCE] knob until the [ST SOURCE] indicator flashes.

Rotate the [ST SOURCE] knob to the left until the volume decreases to the point that

lowers as loud as that of the faintest sounding stereo input.

As the volume becomes fainter, the flashing rate of the [ST SOURCE] indicator becomes slower.

Push the [ST SOURCE] knob to complete the adjustment.

The [ST SOURCE] indicator lights.

Note

Adjustable range: -18dB – 0dB

—

Mono output

Option

Using Microphones

Mono output

down

Stereo output (*1)

MA2030 has two microphone inputs. We recommend that you first set the playback volume of the external

devices before adjusting the volume balance of the microphones.

Phone

XLR

Euroblock

MA2030 front panel

Turn the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer all the way to the left.

Connect a microphone to the [MIC IN 1] jack or the [MIC IN 2] connector.

Gradually turn the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer to the right while

inputting signal to a microphone, making sure that sound is output from the speakers.

You can also confirm the [MIC IN 1] jack input signal by the [MIC IN 1] indicator.

Note

• To adjust the [MIC IN 2 GAIN] trimmer, use a slotted screw driver.

PA2030 rear panel

• Refer to "Attaching Euroblock Plugs" for installation of Euroblock plugs.

• The input signal is always processed through a high pass filter (120Hz, 12dB/oct.) to cut off low frequency signals

as well as a Feedback Suppressor to suppress howling.

• If it is difficult to match the volume balance of the stereo input and the microphone input, lower the stereo input

volume (refer to "Matching the volume levels of external devices" in "Step 4 Adjusting Volume") and then adjust the

Jack type

microphone input volume with the [MIC IN 1] knob or the [MIC IN 2 GAIN] trimmer.

Ducker (lowering the volume of the other channels automatically when a

microphone signal is input)

[SETUP] DIP switch 2/3

Jack/connector

[MIC IN 1]

[SETUP] DIP switch

Ducker disabled

Ducker enabled

down

[SETUP] DIP switch

Option

Operating with Control Panel

Leveler disabled

Leveler enabled

down

Connecting Yamaha Digital Control Panel DCP1V4S to MA2030 enables you to control the volume, to switch

inputs, etc. remotely.

RJ-45

Power cord

To AC outlet

MA2030 rear panel

Ethernet straight cable

(CAT5e or more; 200m or less)

The functions of the knob and the switches of DCP1V4S can be configured with DIP switches at the back of

DCP1V4S.

Panel

DIP switch

Knob

Switch 1

1 2 3 4

Stereo 1

Mic. 1

Volume

Mic. 1

Mic. 2

Mic. 1

Note

Refer to "DCP1V4S Owner's Manual" for DCP1V4S installation.

Option

PA2030 front panel

Connecting the MA2030 and PA2030 lets you increase the number of driven speakers. Connect the [LINE

OUT] jacks of MA2030 and the [LINE IN] jacks of PA2030.

Connecting Speaker Cables

The [SPEAKERS] output connectors on the rear panel are barrier strip type connectors. The connections

are described below for two methods: using a spade lug and using a bare conductor.

Caution

Ensure that load is not applied to the speaker cable.

Note

Connect the cables so that the amplifier's "+" and "-" symbols match those of the speaker. If they are reversed,

the phase will be reversed and the sound will not be output correctly.

When using a spade lug

Loosen the screw, insert the spade lug all the

way from below, and tighten the screw.

≥3.2mm

(≥ 0.13")

≤5.8mm

Euroblock

(≤0.23")

Attaching Euroblock Plugs

MA2030 rear panel

Terminal

screw

Euroblock plug

Note

• You must use the supplied Euroblock plugs. If the plugs have been lost, please contact your Yamaha dealer.

• To prepare the cable for attachment to a Euroblock connector, strip the wire as shown in the illustration using

• Do not tin (solder) the exposed end.

[MIC IN 2]

Note

• If both Duckers of the [MIC IN 1] jack and the [MIC

Loosen terminal screws.

IN 2] jack are enabled, the Ducker for the [MIC IN

1] takes priority.

Insert cables.

• Activating the Ducker lowers the output volume of

down

the stereo inputs by 24dB and mutes that of the

Securely tighten terminal screws.

other microphone input.

Insert the Euroblock plug into the [MIC IN 2] terminal of MA2030 or the [LINE IN]

terminal of PA2030.

Panel Lock

Yamaha Digital Control Panel

Changes by several knobs can be locked, so that the settings of the device are not affected by accidental

DCP1V4S

touch or unauthorized operation. The [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE]

(maximum: one unit)

knobs can be locked.

Adjust the [ST SOURCE], [SOURCE EQ BASS] and [SOURCE EQ TREBLE] knobs

Rear panel

to the desired fixed settings.

When connecting to MA2030,

set the DIP switch 4 to ON

Turn off the power.

(termination setting).

Set DIP switch 8 to the downward position.

Sets the panel ID

Turn the power back on again.

Note

To unlock, turn off the power, set DIP switch 8 to the upward position, and turn on the power.

Volume: Adjusts the volume output

Switch 2

Switch 3

Switch 4

to the [SPEAKERS] terminals and

the [LINE OUT] jacks.

—

Stereo 1/2/3: Switches to stereo

input 1/2/3.

Mic. 1/2: Turns on/off microphone

Stereo 2

Stereo 3

—

input 1/2. When a microphone

is on, the switch indicator of the

Mic. 2

Mic. 1

Mic. 2

control panel lights and the stereo

input is muted.

Mic. 2

Mic. 1

Mic. 2

• If the panel ID is set to 3, the

stereo input is not muted even

though the microphone is on.

—

Mic. 1

—

• If the panel ID is set to 7, the

microphone stays on while

—

Mic. 2

—

holding the switch.

: A chime sounds when the

Mic. 2

—

microphone is turned on/off

—: Does not work. (No function is

assigned.)

Mic. 2

—

Expanding Speakers

RCA

MA2030 rear panel

PA2030 rear panel

When using a bare conductor

Loosen the screw, wrap the conductor wire around

the barrier strip terminal, and tighten the screw. Be

sure that the bare wire does not touch the chassis.

Speaker cable

Wire

should not

touch the

chassis.

15mm*

(0.6")

* Actual size

Loosen

Approx. 5 mm

Slotted

(approx. 0.2")

Tighten

screwdriver

stranded wire to make connections. With a Euroblock connection, stranded wires may be prone to breakage

because of metal fatigue due to the weight of the cable or due to vibration. When rack mounting your device,

use a lacing bar when possible to bundle and fasten the cables.