Yamaha DXS12 mkll Kullanıcı El Kitabı - Sayfa 2

Hoparlör Sistemi Yamaha DXS12 mkll için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Yamaha DXS12 mkll 2 sayfaları. Dxr and dxs series powered speakers and subwoofers
Ayrıca Yamaha DXS12 mkll için: Kullanıcı El Kitabı (22 sayfalar), Manuel (12 sayfalar), Kullanıcı El Kitabı (22 sayfalar), Kullanıcı El Kitabı (2 sayfalar), (İngilizce) Kullanım Kılavuzu (22 sayfalar), (İngilizce) Kullanım Kılavuzu (22 sayfalar), (Rusça) (22 sayfalar)

Sayfayı Yazdır

Setup of Cardioid Mode

Because directivity in the low frequency range is weak, the output sound from the subwoofer diffracts not

only toward the audience but also to the stage in almost the same sound pressure. By using the Cardioid

mode, bass to the audience is summed up and bass to the stage is canceled. This suppresses the bass volume

on the stage, providing a greater allowance before howling, and provides more powerful bass for the audi-

ence.

NOTE

• Use the same model and input signal for the DXS. You can also use the units connected in daisy chain

fashion with setting the OUTPUT jack to [THROUGH].

• To obtain the optimum Cardioid characteristics, locate the cabinet away from walls by more than 1.2 m.

Two-unit, side-by-side placement

Place the two DXS units facing in opposite directions. Set the CARDIOID switch of the DXS facing the

audience to off, and that of the DXS facing the stage to on. Make sure that the other settings (LEVEL,

POLARITY, X-OVER) of the units are set the same.

From left

From mixer

DXS

To right

To full-range

DXS

speaker

Off

*1 When a full-range speaker is connected subse-

quently.

*2 When a full-range speaker is connected subse-

quently and the high pass filter in the full-range

From mixer

speaker is not used, set this to [HPF POST].

To full-range speaker

Stage

To AC outlet

Audience

Two-unit, vertically stacked placement

You can also construct a system for Cardioid mode by vertically stacking two units. Set the CARDIOID

switch of the DXS facing to the stage side to on. Make sure that the other settings (LEVEL, POLARITY, X-

OVER) of the units are set the same.

CAUTION

• When vertically stacking DXS units, make sure they are stable and not in danger of

falling over.

• Align the rubber feet of the upper DXS unit to the feet cups of the lower DXS.

• When using vertically stacked DXS units, do not place any objects (such as full-range

speakers or another DXS) on top of them or insert speaker poles.

To full-range speaker

From lower

DXS

To full-range

speaker

To AC outlet

From mixer

Stage

To upper

DXS

Audience

*1 When a full-range speaker is connected subsequently.

*2 When a full-range speaker is connected subsequently and

the high pass filter in the full-range speaker is not used, set

this to [HPF POST].

Three-unit, side-by-side placement

Set the CARDIOID switch of only the DXS unit facing the stage to on. Set the levels of the two DXS units

facing the audience to the same. Set the level of the DXS unit facing to the stage approximately 6 dB greater

than the DXS units facing the audience.

From center

From mixer

DXS

To center

DXS

Off

From mixer

To AC outlet

Audience

From left

DXS

To right

DXS

About Cardioid mode

The distance between a speaker (A) facing to the audience sound source speaker and another speaker (B)

facing to the stage is defined as d. A delay is applied to the sound from speaker B, equivalent to distance d.

Waveform

from A

Reverse

Stage

polarity

side

delay

Waveform

from B

Sound is

cancelled

Stage side

Off

Directional characteristics

The sound of each speaker is cancelled on the stage

side and summed together on the audience side. The

directional characteristics of this combination are

represented in the polar pattern illustration at right.

Stage

Since the form resembles a heart shape, it is called

side

Cardioid mode.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE

PROCEEDING

Please keep this manual in a safe place for future

reference.

WARNING

Always follow the basic precautions listed below

to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting,

damages, fire or other hazards. These precautions

include, but are not limited to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such as

Off

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip

over, or roll anything over it.

• Only use the voltage specified as correct for the device.

The required voltage is printed on the name plate of the

device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the

Stage

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt

or dust which may have accumulated on it.

• When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is

not unplugged from the wall AC outlet, the device will not

be disconnected from the power source.

•

Remove the electric plug from the outlet when the

device is not to be used for extended periods of time, or

during electrical storms.

•

Be sure to connect to an appropriate outlet with a

protective grounding connection. Improper grounding

can result in electrical shock, fire, or damage.

Do not open

• This device contains no user-serviceable parts. Do not

open the device or attempt to disassemble the internal

parts or modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers

(such as vases, bottles or glasses) containing liquids

which might spill into any openings. If any liquid such as

water seeps into the device, turn off the power

immediately and unplug the power cord from the AC

outlet. Then have the device inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Hearing loss

• Do not use the device for a long period of time at a high or

uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing

loss or ringing in the ears, consult a physician.

• Before connecting the device to other devices, turn off the

power for all devices. Also, before turning the power of all

devices on or off, make sure that all volume levels are set

to the minimum. Failing to do so may result in hearing

loss, electric shock, or device damage.

• When turning on the AC power in your audio system,

Reverse

always turn on the device LAST, to avoid hearing loss and

Audience

polarity

speaker damage. When turning the power off, the device

side

delay

should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open flames near the

device, since they may cause a fire.

If you notice any abnormality

• If any of the following problems occur, immediately turn

off the power switch and disconnect the electric plug from

the outlet.

- The power cord or plug becomes frayed or damaged.

Sound is summed

- Unusual smells or smoke are emitted.

* This is the optimum state,

in which the distance d is a

NOTICE

quarter of the wavelength.

To avoid the possibility of malfunction/damage to the product, or damage to other property, follow the notices below.

 Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, AV equipment, mobile phone, or other electric devices. Otherwise, the

device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater,

or in a car during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the

internal components.

• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved

from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is

present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for sev-

eral hours without turning on the power until the condensation has completely dried out.

• When placing the speaker face down, always place it on a flat surface.

• Do not touch the speaker driver unit.

Audience side

• Air blowing out of the ports is normal.

• Always turn the power off when the device is not in use.

 Connectors

• XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (–).

Information

 About this manual

• The illustrations as shown in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective

Audience

companies.

side

 About disposal

• This product contains recyclable components. When disposing of this product, please contact the appropriate local

authorities.

In Finland: Laite on liitettävä suojamaadoituskosketti-

milla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the

device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualified

Yamaha service personnel.

• If this device should be dropped or damaged,

immediately turn off the power switch, disconnect the

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

electric plug from the outlet, and have the device

DO NOT REMOVE COVER (OR BACK).

inspected by qualified Yamaha service personnel.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

The above warning is located on the rear of the unit.

Always follow the basic precautions listed below

to avoid the possibility of physical injury to you or

Explanation of Graphical Symbols

others, or damage to the device or other property.

Explication des symboles

These precautions include, but are not limited to,

the following:

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Power supply/power cord

L'éclair avec une flèche à l'intérieur d'un triangle équilatéral est destiné à attirer l'attention de l'utilisateur sur la présence d'une « ten-

sion dangereuse » non isolée à l'intérieur de l'appareil, pouvant être suffisamment élevée pour constituer un risque d'électrocution.

• When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and mainte-

by the cord can damage it.

nance (servicing) instructions in the literature accompanying the product.

Le point d'exclamation à l'intérieur d'un triangle équilatéral est destiné à attirer l'attention de l'utilisateur sur la présence d'instruc-

Location

tions importantes sur l'emploi ou la maintenance (réparation) de l'appareil dans la documentation fournie.

• Do not place the device in an unstable position where it

might accidentally fall over and cause injuries.

IMPORTANT SAFETY INSTRUC-

• When installing the device:

- Make sure the top surface faces up; do not install on its

TIONS

sides or upside down.

- Do not use the device in a confined, poorly-ventilated

1 Read these instructions.

location.

2 Keep these instructions.

Inadequate ventilation can result in overheating, possibly

3 Heed all warnings.

causing damage to the device(s), or even fire. Make sure

4 Follow all instructions.

that there is adequate space around the device: at least

5 Do not use this apparatus near water.

30 cm above, 30 cm at the sides and 30 cm behind.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accor-

• Do not use the speaker's handles for suspended

dance with the manufacturer's instructions.

installation. Doing so can result in damage or injury.

8 Do not install near any heat sources such as radiators,

• Do not hold the bottom of the device when transporting or

heat registers, stoves, or other apparatus (including

moving it. In doing so, you may pinch your hands under

amplifiers) that produce heat.

the device, and result in injury.

9 Do not defeat the safety purpose of the polarized or

• Do not press the rear panel of the device against the wall.

grounding-type plug. A polarized plug has two blades

Doing so may cause the plug to come in contact with the

with one wider than the other. A grounding type plug has

wall and detach from the power cord, resulting in short

two blades and a third grounding prong. The wide blade

circuiting, malfunction, or even fire.

or the third prong are provided for your safety. If the pro-

• Do not place the device in a location where it may come

vided plug does not fit into your outlet, consult an electri-

into contact with corrosive gases or salt air. Doing so may

cian for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

result in malfunction.

particularly at plugs, convenience receptacles, and the

• Avoid being near the device during a disaster, such as an

point where they exit from the apparatus.

earthquake. Since the device may turn over or fall and

11 Only use attachments/accessories specified by the man-

cause injury, stay away from the device quickly and move

ufacturer.

to a safe place.

12 Use only with the cart, stand, tripod,

• Before moving the device, remove all connected cables.

bracket, or table specified by the manu-

• When transporting or moving the device, always use three

facturer, or sold with the apparatus. When

or more people. Attempting to pick this unit up with only

a cart is used, use caution when moving

one or two people may result in lower back injuries, or the

the cart/apparatus combination to avoid

equipment may be dropped and damaged, resulting in

injury from tip-over.

injury.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

• Be sure to adhere to the conditions for "Installing a

Speaker Pole" when mounting the speaker on top using

14 Refer all servicing to qualified service personnel. Servic-

ing is required when the apparatus has been damaged in

the pole socket.

any way, such as power-supply cord or plug is damaged,

Tipping this unit over may break the unit, cause damage

liquid has been spilled or objects have fallen into the

to the internal parts or result in personal injury.

apparatus, the apparatus has been exposed to rain or

Maintenance

moisture, does not operate normally, or has been

dropped.

• Remove the power plug from the AC outlet when cleaning

the device.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

Handling caution

DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS-

TURE.

• Do not insert your fingers or hands in any gaps or

openings on the device (ports).

• Avoid inserting or dropping foreign objects (paper,

plastic, metal, etc.) into any gaps or openings on the

device (ports). If this happens, immediately turn off the

power unplug the power cord from the AC outlet, and

have the device inspected by qualified Yamaha service

personnel.

• Do not operate the device if the sound is distorting.

Prolonged use in this condition could cause overheating

and result in fire.

FCC INFORMATION (U.S.A.)

• Avoid pulling the connected cables to prevent injuries or

damage to the device by causing it to fall.

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

Yamaha cannot be held responsible for damage caused

tions not expressly approved by Yamaha may void your

by improper use or modifications to the device.

authority, granted by the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories

PA_en_8

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class

"B" digital devices. Compliance with these requirements pro-

vides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment gen-

erates/uses radio frequencies and, if not installed and used

according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authori-

ties or dealer and ask for the correct method of disposal.

이 기기는 가정용(B급) 전자파적합기기로서 주로 가

Yamaha Pro Audio global website:

정에서 사용하는 것을 목적으로 하며, 모든 지역에서

https://www.yamaha.com/proaudio/

사용할 수 있습니다.

Yamaha Downloads:

(class b korea)

https://download.yamaha.com/

ATTENTION

RISQUE DE CHOC

ELECTRIQUE-NE PAS OUVRIR

ATTENTION :

POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER

LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT

L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,

FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.

L'avertissement ci-dessus est situé sur l'arrière de l'unité.

PRÉCAUTIONS CONCERNANT

LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d'eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l'appa-

reil conformément aux instructions du fabricant.

8 Ne pas installer l'appareil à proximité d'une source de

chaleur comme un radiateur, une bouche de chaleur, un

poêle ou tout autre appareil (y compris un amplificateur)

produisant de la chaleur.

9 Ne pas modifier le système de sécurité de la fiche polari-

sée ou de la fiche de terre. Une fiche polarisée dispose de

deux broches dont une est plus large que l'autre. Une

fiche de terre dispose de deux broches et d'une troisième

pour le raccordement à la terre. Cette broche plus large

ou cette troisième broche est destinée à assurer la sécur-

ité de l'utilisateur. Si la fiche équipant l'appareil n'est pas

compatible avec les prises de courant disponibles, faire

remplacer les prises par un électricien.

10 Acheminer les cordons d'alimentation de sorte qu'ils ne

soient pas piétinés ni coincés, en faisant tout spécialem-

ent attention aux fiches, prises de courant et au point de

sortie de l'appareil.

11 Utiliser exclusivement les fixations et accessoires spécif-

iés par le fabricant.

12 Utiliser exclusivement le chariot, le stand,

le trépied, le support ou la table recom-

mandés par le fabricant ou vendus avec

cet appareil. Si l'appareil est posé sur un

chariot, déplacer le chariot avec précau-

tion pour éviter tout risque de chute et de blessure.

13 Débrancher l'appareil en cas d'orage ou lorsqu'il doit res-

ter hors service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire

réparer l'appareil s'il a subi tout dommage, par exemple

si la fiche ou le cordon d'alimentation est endommagé, si

du liquide a coulé ou des objets sont tombés à l'intérieur

de l'appareil, si l'appareil a été exposé à la pluie ou à de

l'humidité, si l'appareil ne fonctionne pas normalement

ou est tombé.

AVERTISSEMENT

(UL60065_03)

POUR RÉDUIRE LES RISQUES D'INCENDIE OU DE

DÉCHARGE ÉLECTRIQUE, N'EXPOSEZ PAS CET APPA-

REIL À LA PLUIE OU À L'HUMIDITÉ.

(UL60065_03)

that interference will not occur in all installations. If this product

is found to be the source of interference, which can be deter-

mined by turning the unit "OFF" and "ON" , please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

(class B)

(weee_eu_en_02)

Manual Development Group

Published 05/2018 YJMAW-B0