Directed Directechs DB3 Kurulum Kılavuzu - Sayfa 3

Otomobil Aksesuarları Directed Directechs DB3 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Directed Directechs DB3 18 sayfaları. Smart key for 2013 toyota highlander
Ayrıca Directed Directechs DB3 için: Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Manuel (6 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (10 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (10 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (17 sayfalar), Kurulum Kılavuzu (20 sayfalar)

Sayfayı Yazdır

Directed Directechs DB3 Kurulum Kılavuzu

Introduction

DB3 is an all-in-one door lock and override module.

Warning!

This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs

Mobile application for smartphones. Refer to <ConnectImportant> for more information.

Pre-installation and application warnings

Firmware notes: This section highlights important information for this specific firmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

No takeover feature is available on Push-to-Start vehicles. The vehicle will shut down as soon as a door is opened.

To remote start the engine, the hood, hatch, and all doors MUST be closed.

Keyless and Smart Key will remain functional during remote start.

The optional Plug & Play TLTH1/THTOD1 T-Harness is sold separately.

The OBDII Diagnostic Connector features will remain the same even when the T-Harness is installed.

All connectors are displayed from the wire side (unless specified otherwise).

Refer to the "Vehicle connections" following the installation diagram.

General notes: This section highlights important information for this specific firmware.

Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D

[1]

Connection required ONLY if Pit Stop/Idle mode is desired.

[2]

Autolights Interrupt ONLY required if vehicles are equipped with Autolights.

[3]

Key type

Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings.

H-stam ped keys

For vehicles with H-stamped keys, see

the TL10 firmware.

OEM remote starter detection

How to know if the vehicle is equipped with an OEM remote starter

1. An "ENGINE STARTER"

sticker should be on the remote.

403.TL1 5.07.106 2013 Toyota Highlander (Smart Key)

TLTH1/THTOD1

G-stam ped keys

For vehicles with G-stamped keys, see

the TL5 & TL7 firmware.

2. Remote start the OEM remote starter:

Press the remote control's lock button twice within 2 seconds, then press and hold the lock

button for 3 seconds.

Keys required for

programming

For vehicles with dot-stamped keys,

see the TL11 firmware.

Note:

Some replacement keys

may not have any markings on

the key.

Press & Hold

for 3 seconds

Keys required for

operation

Standard Key