Directed Xpresskit DBALL2 Kurulum Kılavuzu - Sayfa 3

Otomobil Aksesuarları Directed Xpresskit DBALL2 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Directed Xpresskit DBALL2 19 sayfaları. Ford5 remote start ready (rsr) installation
Ayrıca Directed Xpresskit DBALL2 için: Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (18 sayfalar), Manuel (14 sayfalar), Kurulum Kılavuzu (13 sayfalar), Kurulum Kılavuzu (14 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (15 sayfalar), Kurulum ve Hızlı Referans Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar), Manuel (19 sayfalar), Kurulum Kılavuzu (11 sayfalar), Kurulum Kılavuzu (10 sayfalar)

Sayfayı Yazdır
Directed Xpresskit DBALL2 Kurulum Kılavuzu
Platform: DBALL2
Firmware: HYUNDAI4 Remote Start Ready (RSR) Installation
Installation Type 1
Refer to the Vehicle Wiring Reference Chart on page 4 for wire color and component location.
(-) PTS 1:
Orange/Black, pin 3
3
1
2
4 5
M04
(black conn. at
PTS switch)
16
15
14
13
12
(-) PTS 2:
Yellow/Orange,
pin 2

M01-L

(white conn. at headlight switch)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
(-) Parking Lights:
Pink, pin 15
(+) Starter:
Pink, pin 11
(+) Accessory:
Yellow, pin 3
(+) Ignition:
Green, pin 21
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[1]
With the exception of the OBDII Diagnostic connector, all adapters are displayed from the wire side (unless specified otherwise).
6 7
8
11
10
9
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
(+) 12V: Brown: 7
Ignition 1 Output: Yellow: 8
(-) Ground: Black: 14
(-) Push-To-Start 1: Black/White: 1
(-) Push-To-Start 2: Green/Black: 2
(-) Parking Lights: Red/Black: 4
(+) Accessory Output: Gray: 6
(+) Starter Output: Gray/Black: 7
EMS COM Data: Orange/Black: 11
EMS COM:
White/Orange, pin 32
EM11
(black conn. in driver kick panel)
10
20
30
48
(+) 12V: Red: 13
RF
Prog. Button
LED
MF11
(white conn. in driver kick panel)
9 8 7 6
5 4 3 2
1
19 18 17 16 15 14 13 12
11
29 28 27 26 25
24
23
22
21
38 37 36 35 34
33
32
31
47 46 45 44 43
42 41
40
39
B-CAN Low:
Red, pin 33
B-CAN High:
Blue, pin 24
OBDII
1
Diagnostic
connector
9
C-CAN Low:
Orange, pin 14
Hood Pin
Note: hood pin only required
on vehicles not equipped with a
factory hood pin
Remote Start Safety
Override Switch
6: White/Black: (-) Hood
DBALL2
You can connect to either a XL202
RFTD OR a SmartStart module.
Refer to the SmartStart/XL202
Installation Notes for more information.
© 2016 Directed. All rights reserved.
Rev.: 20161207
Page 3
C-CAN High:
Green, pin 6
8
16
(+) 12V:
Gray/Black,
pin 16