Zanussi ZSFN121W1 Kullanıcı Kılavuzu - Sayfa 10
Bulaşık Makinesi Zanussi ZSFN121W1 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Zanussi ZSFN121W1 25 sayfaları.
Sayfayı Yazdır
All the consumption values mentioned
in this section are determined in
accordance with the currently
applicable standard in laboratory
conditions with water hardness
2.5mmol/L according to the
2019/2022 regulation (water softener:
level 3).
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
How to set the water softener level
The appliance must be in programme selection
mode.
Make sure that the programme marker on the knob
is in the on/off position.
1. To enter the user mode, press and hold
the same time turn the knob counterclockwise
until the programme marker indicates the first
programme. Release the
indicators
and on/off start flashing.
The intermittent flashing of
setting, e.g. 5 flashes + pause + 5 flashes = level
5.
2. Press
repeatedly to change the setting.
Each pressing of
number. After reaching level 10, the count
starts again from level 1.
3. To confirm the setting, turn the programme
knob until the programme marker is again in the
on/off position
THE RINSE AID EMPTY NOTIFICATION
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically released
during the hot rinse phase.
When the rinse aid chamber is empty, the rinse aid
indicator is turned on notifying to refill rinse aid. If
the drying results are satisfactory while using multi-
tablets only, it is possible to deactivate the
notification for refilling rinse aid. However, for best
drying performance, always use rinse aid.
If standard detergent or multi-tablets without rinse
aid are used, activate the notification to keep the
rinse aid refill indicator active.
How to deactivate the rinse aid empty
notification
The appliance must be in programme selection
mode.
10
. At
when the
shows the current
increases the level
Make sure that the programme marker on the knob
is set to the on/off position.
1. To enter the user mode, press and hold
the same time turn the knob counterclockwise
until the programme marker indicates the first
programme. Release
and on/off start flashing.
2. Turn the knob counterclockwise until the
programme marker indicates the second
programme.
The indicator
shows the current setting:
•
is on = the rinse aid empty notification
is activated.
•
is off = the rinse aid empty notification
is deactivated.
3. Press
to change the setting.
4. To confirm the setting, keep turning the
programme knob until the programme marker is
back in the on/off position.
THE RINSE AID LEVEL
It is possible to set the released quantity of rinse
aid between level 1 (minimum quantity) and level 8
(maximum quantity). Level 0 deactivates the rinse
aid dispenser and no rinse aid is released. Factory
setting: level 5.
How to set the rinse aid level
The appliance must be in programme selection
mode.
Make sure that the programme marker on the knob
is set to the on/off position.
1. To enter the user mode, press and hold
the same time turn the knob counterclockwise
until the programme marker indicates the first
programme. Release
and on/off start flashing.
2. Turn the knob counterclockwise until the
programme marker indicates the third
programme.
The indicator
shows the current setting, e.g. 5
flashes + pause + 5 flashes = level 5.
3. Press
to change the setting.
4. To confirm the setting, keep turning the
programme knob until the programme marker is
back in the on/off position.
AIRDRY
AirDry improves the drying results with less energy
consumption. The appliance door opens
. At
when the indicators
. At
when the indicators