Directed Directechs DB3 Kurulum Kılavuzu - Sayfa 4

Kontrol Ünitesi Directed Directechs DB3 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Directed Directechs DB3 18 sayfaları. Smart key for 2013 toyota highlander
Ayrıca Directed Directechs DB3 için: Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Manuel (6 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (10 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (10 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (17 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (18 sayfalar)

Sayfayı Yazdır

Directed Directechs DB3 Kurulum Kılavuzu

Pre-installation and application warnings

Firmware notes: This section highlights important information for this specific firmware and will assist in pricing

accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

IMPORTANT:

Before attempting to program your module, you must first check if your vehicle is equipped with an OEM remote starter

and disable it. If the vehicle is equipped with an OEM remote starter, whether Active or Inactive, it MUST be temporarily disabled

or permanently disconnected depending on the vehicle. Please refer to the "OEM remote starter information" section of the guide for

additional details.

Note: In some cases, the module will program to the vehicle even if equipped with an OEM starter, but will prevent the aftermarket remote

start from functioning properly.

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.

If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before installing the DB3 module, otherwise it

will not program.

No takeover feature is available on Push-to-Start (PTS) vehicles.

Keyless and Smart Key will remain functional during remote start.

Refer to "Vehicle connections" following the wiring diagram.

Aux 1 = Left Sliding Door; Aux 2 = Right Sliding Door: Applicable on the Toyota Sienna (Smart Key) ONLY.

General notes: This section highlights important information for this specific firmware.

Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D. Also please note that by

[1]

default, the tach is set to 1000 rpm on hybrid vehicles.

The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin or NOT

[2]

supported in data.

The Push-to-Start (PTS) is required ONLY if Pit-Stop/Idle mode is desired.

[3]

403.TL2 4.15 2019 Lexus GX 460 (Smart Key)

Keys required for

programming

operation