Directed Xpresskit DBALL2 Kurulum Kılavuzu - Sayfa 10

Kilitler tarafından Directed Xpresskit DBALL2 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Directed Xpresskit DBALL2 16 sayfaları. Ford5 remote start ready (rsr) installation
Ayrıca Directed Xpresskit DBALL2 için: Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (18 sayfalar), Manuel (14 sayfalar), Kurulum Kılavuzu (13 sayfalar), Kurulum Kılavuzu (14 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (15 sayfalar), Kurulum ve Hızlı Referans Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar), Manuel (19 sayfalar)

Sayfayı Yazdır
Directed Xpresskit DBALL2 Kurulum Kılavuzu
Platform: DBALL2
Firmware:
CHRYSLER11 ange Extender
Feature & Option List
Feature & Option List
It is recommended to configure all
flashing page on www.directechs.com. The web offers more options such as
configuration of the features is possible using the information on this page.
* Default Option
Feat.
Operation
1
RFTD Output Type
Automatic climate
2
control when
remote started

Feature Programming

To enter feature programming routine
-
Turn t
he ignition
ON
, then
-
Within 5 seconds, press and
Programming button.
-
The
LED
will flash green once slowly
the current option of feature 1
until
a new command is entered
Changing feature options
-
Press the
lock/
arm or
unlock/
-
The
LED
flashes
red
rapidly the number of times equal to the current option number. After a short delay, the
the number of times to indicate the current feature.
Accessing another feature
-
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-
The
LED
flashes green slowly the number of times equal to the feature number. After a short delay, the
indicate the current option of the current feature.
When the maximum number of features or options is reached, the
Once a feature is programmed
-
Other features can be programmed.
-
The feature programming can be exited.
Exiting feature programming
-
No activity for 30 seconds; after 30 seconds, the
sequence.
OR
-
Press and
HOLD
the programming button for 3 seconds. After 3 seconds, the
end of the programming sequence.
R
Ready
the
features and options listed below
Flashes/Options
1. No RF Output*
Module is connected to a remote starter using a standard installation.
2. RFTD Output
Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart
Module is connected to SmartStart using an RSR or RXT installation (when available).
1. OFF*
Climate controls return to last setting.
2. ON
Climate controls are automatically set based on temperature.
OFF
.
HOLD
the rogramming button
p
to indicate the feature number is 1. After a short delay, the
(i.e. 1x green followed by 1x red indicates feature 1 is set to option 1) The flashing sequence will
.
disarm button on aftermarket transmitter to change the option of the selected feature.
The flashing sequence will
The flashing sequence will
LED
will turn
(RXT)
Installation
using
the
configuration tool found on the module
EIPS
and
Description
until the
LED
turns
ON
orange (
repeat until
a new command is entered
repeat until
a new command is entered
LED
will start flashing again from the first feature or option.
ON
orange for 2 seconds to confirm the end of the programming
LED
will turn
ON
Rev.: 20170724
RXT
; however, manual
Programming
Button
after 3 seconds . Release the
)
LED
flashes
red
rapidly to indicate
.
LED
flashes green slowly
.
LED
flashes red rapidly to
.
orange for 2 seconds to confirm the
© 2017 Directed. All rights reserved.
Page 10
repeat