Directed Xpresskit DBALL2 Kurulum Kılavuzu - Sayfa 10

Kilitler tarafından Directed Xpresskit DBALL2 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Directed Xpresskit DBALL2 18 sayfaları. Ford5 remote start ready (rsr) installation
Ayrıca Directed Xpresskit DBALL2 için: Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (18 sayfalar), Manuel (14 sayfalar), Kurulum Kılavuzu (13 sayfalar), Kurulum Kılavuzu (14 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (15 sayfalar), Kurulum ve Hızlı Referans Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (16 sayfalar), Manuel (19 sayfalar)

Sayfayı Yazdır
Directed Xpresskit DBALL2 Kurulum Kılavuzu
Platform: DBALL2
Firmware:
CHRYSLER Remote Start Ready
Feature
&
Option List
It is recommended to configure all
flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible
using the information on this page.
* Default option
Feature
Operation
1
RF Output Type
2
Unlock Driver Priority
3
Trunk
4
Aux1
5
Aux2
Automatic Controlled
6
Door Lock
Smart OEM Alarm
7
Control
4
the
features and options listed below
Flashes / Option
1. Disabled*
2. RFTD Output
3. SmartStart
1. Driver Priority*
2. All
1. Disabled
2. Trunk*
3. Right Sliding Door
4. Left Sliding Door
1. Disabled*
2. Trunk
3. Right Sliding Door*
4. Left Sliding Door
1. Disabled
2. Trunk
3. Right Sliding Door
4. Left Sliding Door*
1. Disabled*
2. With Ignition
3. With Brake
4. With Speed
1. Disabled
2. Safelock
3. Enabled*
(RSR)
Installation
using
the
Module is connected to a remote starter using a standard installation.
Module is connected to an XL202 using an RSR or RXT installation (when available).
Module is connected to SmartStart using an RSR or RXT installation (when available).
Unlocks only the driver door on first press and unlocks all doors on a second press within
5 seconds.
Unlocks all doors on first press.
1. Disabled: doesn't operate any function in the vehicle.
2. Trunk/Tail Glass: Will pop the trunk or if not available, will pop the tail glass.
3./4. Right/Left Sliding Door: When available, will operate the sliding door.
No operation.
Locks all doors when ignition is ON. Unlocks all doors when ignition turns OFF.
Locks all doors when brake pedal is pressed while the vehicle is running. Unlocks all
doors when ignition turns OFF.
Not available
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm
command will be executed at the beginning or end of the sequence; it must be controlled
by the Remote Starter.
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote
starter. It will unlock at the beginning of the sequence, and relock after start and
shutdown.
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and
rearm the vehicle in the remote start sequence, only when required. The reason for this is,
factory alarm control must often be done by lock or unlock operation. This could create
unnecessary actions on door lock modules, such as the horn to honk. When possible,
Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the
disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory
alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor
the remote starter actions so that the factory alarm control is not done twice. A remote
starter, for which the Safelock feature is active, will work perfectly with this option and will
make it invisible to the user.
configuration tool found on the module
Description
© 2017 Directed. All rights reserved.
Rev.: 20170817
Page 10