Directed Xpresskit DBALL2 Manuel - Sayfa 17

Kilitler tarafından Directed Xpresskit DBALL2 için çevrimiçi göz atın veya pdf Manuel indirin. Directed Xpresskit DBALL2 19 sayfaları. Ford5 remote start ready (rsr) installation
Ayrıca Directed Xpresskit DBALL2 için: Kurulum Kılavuzu (12 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (18 sayfalar), Manuel (14 sayfalar), Kurulum Kılavuzu (13 sayfalar), Kurulum Kılavuzu (14 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (20 sayfalar), Kurulum Kılavuzu (15 sayfalar), Kurulum ve Hızlı Referans Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar), Kurulum Kılavuzu (18 sayfalar), Kurulum Kılavuzu (16 sayfalar)

Sayfayı Yazdır

Quick Reference Guide

DBALL/DBALL2-FORD5 Remote Start Ready (RSR) Installation

Vehicle Takeover with Get In and Go*

Close the vehicle doors, hood and trunk, then press

the Remote Start button on the transmitter to start

the vehicle.**

Press the Unlock button on the factory

or aftermarket remote.**

Complete the following steps within 45 seconds

or the vehicle will shut down.

Enter the vehicle, while making sure the

factory remote is inside with you.

Press the brake pedal, put the car

in gear and drive off.

* Get In and Go connections required.

** Your aftermarket remote may differ from the model shown in the illustrations.

Get In and Go

Get In and Go is designed to provide users with easy takeover when

entering their Push-to-Start (PTS) equipped vehicle, once it has been

remote started.

Typically, users would have to remote start their vehicle, then get inside and press

the vehicle start button to perform a takeover. There is therefore a physical action

required to drive away. With Get In and Go technology, you simply remote start the

vehicle, unlock the doors, get in and go... Nothing to do but put the gear in drive and

enjoy your vehicle.

This unique feature monitors a variety of parameters such as the key fob, vehicle

speed sensor and door sensor, in order to perform takeover securily.

Press

remote start

button**

Press Unlock

button on

either remote**

Enter vehicle

with key fob

Ready to

drive off

Pit Stop Mode

The Pit Stop Mode feature is practical when you need to stop and run an errand,

but wish to keep the engine running.

Stop the vehicle in a safe parking spot

and put the gear in Park (P).

Press the button to remote start the vehicle.*

The PTS button will flash once to

indicate the vehicle is now in Pit Stop

Mode.

It is now safe to leave the engine running and exit the

vehicle with the factory remote in hand.

Note: We recommend that you always lock the doors

of your vehicle when leaving it unattended.

* Your aftermarket remote may differ from the model shown in the illustrations.

Parking Light Error Codes

The parking lights on your vehicle will flash a specific number of times 3 seconds

following an unscheduled shutdown or failure to start. Each flashing pattern is

described below.

Flashes

Diagnostic

Runtime expired.

Over-rev shutdown.

Low/No RPM.

Transmitter shutdown.

Brake shutdown.

Hood shutdown/Remote start safety override switch is ON*.

Remote start safety override switch is ON*.

* If the vehicle hood status is supported through data, it will also report a 7 flash

safety override code.

Stop & put vehicle in Park (P)

Press

ENGINE

START

remote start

STOP

button*

Flashes

Exit vehicle with

Smart Key