Alemite 6320-3 Servis Kılavuzu - Sayfa 6
Kontrol Ünitesi Alemite 6320-3 için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Alemite 6320-3 10 sayfaları. High-pressure control valve
Sayfayı Yazdır
SER 6320-3
CAUTION
Do not damage any portion of Single-Shot
Adjuster (24) during removal of Packing Ring (21).
6. Packing Ring (21) from Single-Shot Adjuster (24).
7. Single-Shot Adjuster from Inlet Adapter (18). The Sin-
gle-Shot Adjuster is under slight spring pressure.
8. Gasket (19), Spring (22), and Single-Shot Valve (23)
from Single-Shot Adjuster.
Upper Portion
9. Aluminum Gasket (14) and Seat assembly (16) from
Body (10).
10. Additional Gaskets (14), Symmetrical Guide (15), and
Spring (13) from the Body.
11. Screw (8), Lock Washer (7), and Support (9) from
Body.
12. Lever and Bracket assembly (2).
13. Setscrew (1) from Lever and Bracket assembly.
14. Packing Plug (3) from the Body.
15. Plunger Stem (11) and Washer (12) from the Body.
16. O-Rings (4 and 6) and Back-Up Washer (5) from the
Packing Plug.
Clean and Inspect
NOTE: Use a repair kit for replacement
parts. Make sure all the components are
included in the kit before discarding used
parts.
Part # (Item #)*
171001-3
(6)
O-Ring, 5/16 " OD
O-Ring, 1/2 " OD
171001-7
(4)
Washer, Back-Up, 3/16 " ID (Leather)
322953
(5)
* Refer to Figure 2 Parts List for Parts Identification
Revision (1-13)
solvents such as methylene chloride or 1,1,1-
trichlorethane in this valve. An explosion can
result when aluminum and/or zinc-plated parts
come in contact with halogenated hydrocarbon
solvents.
1. Clean all metal parts in a modified petroleum-based
2. Inspect all parts for wear and/or damage.
3. Closely inspect the mating surfaces of all components
4. Inspect Valve and Seat assembly (16), Single-Shot
Assembly
1. Lubricated Back-Up Washer (5) small O-Ring (6) into
2. Lubricated O-Ring (4) onto the Packing Plug.
3. Washer (12) onto flats end of Plunger Stem (11).
4. Stem and Washer assembly into the Body.
5. Packing Plug assembly over the Stem and screw into
Description
Table 4 Lubrication Specifications
6
High-Pressure Control Valve
WARNING
Do not use halogenated hydrocarbon
solvent. The solvent should be environmentally safe.
• Replace as necessary.
for any imperfections Ensure a smooth and clean
contact is obtained when assembled.
EXAMPLE: Make sure Valve and Seat
Assembly (16) seats properly.
Valve (23), and Single-Shot Adjuster (24) closely. Use
a magnifying glass to detect any wire draw marks.
N O T E : P r i o r t o a s s e m b l y, c e r t a i n
components require lubrication. Refer to
Table 4 for details.
Install or Screw:
Packing Plug (3).
• Make sure the Washer seats properly.
the Body.
Lubricant
SAE 30 Oil
SAE 30 Oil
Soak 8 hours at room temperature in SAE 30 Oil
Alemite LLC