Nikon Callaway iQ Kullanım Kılavuzu - Sayfa 8

Ölçüm Cihazları Nikon Callaway iQ için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Nikon Callaway iQ 39 sayfaları. Nikon callaway iq laser rangefinder instruction manual
Ayrıca Nikon Callaway iQ için: Kullanım Kılavuzu (28 sayfalar), Manuel (2 sayfalar)

Sayfayı Yazdır

Operational summary

4. Measuring

Note: D epressing and holding down the POWER button causes all

symbols to be displayed in the internal LCD panel. After you

remove your finger from the POWER button, the last-used

setting is displayed. (If you briefly press the POWER button

then remove your finger, the LCD panel may display the last-

used setting without displaying all of the symbols. This is not a

malfunction or other problem.)

Before measuring, be sure to confirm unit setting.

◎

: See the relevant mode section in this manual for setting.

Measurement

1. Press the POWER button for power-on. (Power turns off 8

1. Press the POWER button for power-on.

seconds after the last operation.)

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

Stand-by.

Immediately after power-on.

Stand-by.

Immediately after power-on.

Stand-by.

(Initializing)

2. Aim at the target.

2. Aim at the target

Position the target at the center of the reticle

Target aiming

Target focusing.

[Single measurement]

3. Press POWER button once to start single measurement.

Target focusing.

[Single measurement]

Target focusing.

3. Press POWER button once to start single measurement.

Target focusing.

[Single measurement]

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, "distance" or "fail to measure" indicator are

4. After measurement, "distance" or "fail to measure" indicator are displayed for 8 seconds, then power turns off. If you press the POWER

displayed for 8 seconds, then power turns off. If you press the

button during power-on (while the internal display is lit), another single measurement starts.

POWER button during power-on (while the internal display is lit),

4. After measurement, "distance" or "fail to measure" indicator are displayed for 8 seconds, then power turns off. If you press the POWER

another single measurement starts.

4. After measurement, "distance" or "fail to measure" indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

Upward measurement.

Downward measurement.

unable to measure distance.

Displays the measured figure.

Failure to measure

Downward

[Continuous measurement]

Failure to measure or

Upward

Upward measurement.

Downward measurement.

Failure to measure or

Upward measurement.

Downward measurement.

Failure to measure or

Upward measurement.

Downward measurement.

unable to measure distance.

or unable to

measurement.

unable to measure distance.

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows "distance" and

measurement.

Displays the measured figure.

"fail to measure" indicator alternately.

Displays the measured figure.

measure distance.

Note: Laser irradiaton mark is blinking during the measurement.

[Continuous measurement]

Displays the measured figure.

[Continuous measurement]

Note: If you stop pressing the button, the continuous measuremen stops

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows "distance" and

"fail to measure" indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Failure to measure or

Displays the measured

figure. (Target 1)

figure. (Target 2)

unable to measure distance.

Failure to measure or

Upward measurement.

Downward measurement.

Failure to measure or

Upward measurement.

Downward measurement.

[Continuous measurement]

unable to measure distance.

Displays the measured figure.

3. Keep pressing POWER button to start continuous measurement up

[Continuous measurement]

to approx. 5 seconds. The internal display shows "distance" and "fail to

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows "distance" and

measure" indicator alternately.

"fail to measure" indicator alternately.

Failure to measure or

Upward measurement.

"fail to measure" indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

unable to measure distance.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Displays the measured figure.

Note: If you stop pressing the button, the continuous measuremen stops

Note: If you stop pressing the button, the continuous measurement stops.

[Continuous measurement]

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows "distance" and

"fail to measure" indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Failure to measure or

Displays the measured

Failure to measure or

Displays the measured

Failure to measure or

figure. (Target 1)

figure. (Target 2)

unable to measure distance.

figure. (Target 1)

unable to measure distance.

figure. (Target 1)

figure. (Target 2)

unable to measure

figure. (Target 1)

distance.

Blinks while performing measurements.

Failure to measure or

Displays the measured

figure. (Target 1)

unable to measure distance.

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

4. After continuous measurement, the measured results are displayed for 8

seconds, then power turns off. If you press the POWER button during power-

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

on (while the internal display is active), another measurement starts.

Downward measurement.

When measuring a pin at a golf course, for example,

use Continuous measurement mode for easy

measurement. With no objects between you and

the pin, the smallest number is the distance to your

Downward measurement.

targeted pin.

Displays the measured

figure. (Target 2)

Displays the measured

figure. (Target 2)