ARMORDILLO RS Running Boards Manuel - Sayfa 3
Otomobil Aksesuarları ARMORDILLO RS Running Boards için çevrimiçi göz atın veya pdf Manuel indirin. ARMORDILLO RS Running Boards 8 sayfaları. 2009-2018 doge ram 1500 - crew cab, 2010-2018 ram 2500/3500 - crew cab, 2018-2022 ram 1500 classic - crew cab, excl. chassis cab diesel models
Ayrıca ARMORDILLO RS Running Boards için: Kurulum Talimatları Kılavuzu (6 sayfalar)
Sayfayı Yazdır2007-2019 Chevy Silverado 2500/3500 / GMC Sierra 2500/3500 - Extended Cab/Double Cab
Remove the rubber plug from the larger hole. Select (1) 8mm Clip Nut. Slide the Clip Nut into
the larger hole. Line up the threaded nut with the smaller hole, (Figure 3).
3. Select (1) Driver/Passenger Mounting Bracket. Bolt the Mounting Bracket to the Clip Nuts and/or the
factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers,
(Figure 4). Do not tighten hardware.
4. Repeat Steps 1—3 to attach the remaining (2) Driver/Left Mounting Brackets, (Figures 5 & 6).
5. Select the Driver/Left RS2 Running Board. Attach the Running Board to the rear faces of the (3)
Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers and (6) 10mm Nylon Lock Nuts,
(Figure 7). Do not tighten hardware.
6. Level and adjust the Running Board and fully tighten all hardware.
7. Move to the Passenger/Right side of the vehicle. On the Passenger/Right side, determine if the vehicle
is equipped with a plastic diesel exhaust fluid (DEF) tank, (Figures 8 & 9).
Models without DEF tank, skip to Step 8.
Models with DEF tank: The tank sits close to the side of the body. With specialized tools, the
passenger front upper and lower Bracket can be installed but room is very limited.
Determine model year of vehicle before proceeding.
Up to 2016 models:
It may be easier to drop the tank down to access the inner side of the body panel for upper bracket
installation. Tank will not need to be removed, only dropped down for access to mounting location.
IMPORTANT: If tank is full, it will be very heavy and assistance is highly recommended to avoid injury
or damage to the vehicle or the tank. It is recommended that installation is performed when the DEF
tank is low on fluid before dropping the tank.
a. On models with plastic lower tray under the tank, remove the (3) hex bolts attaching the tray to
the frame, (Figure 8), and remove the tray.
b. Release the tank filler hose. Release the plug for the sending unit on the top of the tank.
c. Support the tank with a floor jack. Place a smooth flat surface, (wooden block for example),
between the floor jack and the tank to avoid damaging the plastic tank. Do not push up on the
tank; only support the weight of the tank with the jack.
d. Remove the (2) bolts securing the tank straps to the vehicle, (Figure 9). Tilt the straps to
release from the brackets. Slowly lower the tank until the top of the tank is almost visible. Use
blocks or stands to support the tank while installing the front Upper and Lower Brackets.
e. Proceed to Step 8.
2017 models and on:
a. Remove the (4) hex bolts attaching plastic cover to DEF tank, (Figure 10A) and remove plastic
cover, (Figure 10B). NOTE: On 2017-on 2500/3500 models, only remove plastic cover from
DEF tank. Do not lower DEF tank and proceed to Step 8.
8. Locate the first tab on the edge of the pinch weld, (Figure 11). Select the Upper Bracket, (Figure 12).
Attach the Upper Bracket with (1) 8mm x 25mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat
Washer, (Figure 13). Do not tighten hardware at this time.
9. Line up the hole in the bottom of the Upper Bracket with the hole in the tab on the pinch weld.
a. Models with a weld-nut: Slide the Bracket over the weld-nut. Attach the Lower Bracket to the
bottom of the body and weld-nut with (1) 8mm x 40mm Hex Bolt, (1) 8mm x 24mm Flat Washer,
(1) 8mm x 28mm Flat Washer and (1) 8mm Nylon Lock Nut, (Figures 14 & 15). Do not tighten
hardware.
b. Models with flat tab and hole: Insert the 8mm Bolt Plate down through the hole in the Upper
Bracket and tab. Attach the Lower Bracket to the bottom of the body and Bolt Plate with (1)
8mm Flat Washer and (1) 8mm Nylon Lock Nut, (Figures 16). Do not tighten hardware.
10. Attach the Lower Bracket to the Upper Bracket with (1) 8mm x 25mm Hex Bolt, (1) 8mm Lock Washer
and (1) 8mm Flat Washer, (Figure 17). Do not tighten hardware.
11. Repeat Steps 1—4 to attach the (2) remaining Passenger/Right Mounting Brackets.
2007-2018 Chevy Silverado 1500 / GMC Sierra 1500 - Extended Cab/Double Cab
Page 3 of 8
RS Running Boards
7/31/20 (AL)