Dirt Devil UP04 Kullanıcı Kılavuzu - Sayfa 15
Elektrikli Süpürge Dirt Devil UP04 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Dirt Devil UP04 20 sayfaları. Lightweight pet upright
Sayfayı Yazdır
MAINTAINING YOUR VACUUM
CLEANER
Replacing The Drive Belt
REPLACING THE DRIVE BELT
The drive belt is not included as spare part, contact Customer Service
helpline on the back page if a replacement is needed.
Make sure the vacuum is switched off and unplugged first.
Check the drive belt carefully for wear, cuts and stressed areas.
Check the drive belt carefully for wear, cuts and stressed areas. If the
If the drive belt appears worn, you will need to replace it. To remove
drive belt appears worn, you will need to replace
the drive belt, read the instructions and follow the drawings below:
it. To remove the drive belt, read the instructions
and follow the drawings below:
1. Grasp the old drive belt and remove from motor
shaft. Discard old drive belt.
1. Grasp the old drive belt and remove from
2. Loop new drive belt over motor shaft and stretch
Replacing The Drive Belt
motor shaft. Discard old drive belt.
other end over floor brush in the space provided
between the bristles.
The drive belt is not included as spare part, contact Customer Service
2. Loop new drive belt over motor shaft and
helpline on the back page if a replacement is needed.
stretch other end over floor brush in the
3. Place ends of floor brush down into slots on sides
as shown. Turn floor brush by hand several times in
space provided between the bristles.
Check the drive belt carefully for wear, cuts and stressed areas. If the
the direction of the motor shaft. If properly installed,
3. Place ends of floor brush down into slots on
drive belt appears worn, you will need to replace
drive belt will align itself on floor brush.
it. To remove the drive belt, read the instructions
sides as shown. Turn floor brush by hand
4. Replace brush cover and six screws.
and follow the drawings below:
several times in the direction of the motor
1. Grasp the old drive belt and remove from
shaft. If properly installed, drive belt will align
motor shaft. Discard old drive belt.
itself on floor brush.
2. Loop new drive belt over motor shaft and
4. Replace brush cover and
stretch other end over floor brush in the
space provided between the bristles.
six screws.
3. Place ends of floor brush down into slots on
sides as shown. Turn floor brush by hand
several times in the direction of the motor
shaft. If properly installed, drive belt will align
itself on floor brush.
4. Replace brush cover and
CHANGING THE FUSE
six screws.
Changing the fuse
1. Only use a 13 amp fuse.
1. Only use a 13 amp fuse.
Changing the fuse
2. To change the fuse, place a screwdriver into the
2. To change the fuse, place a
recess of the plug cover and pull the fuse holder
screwdriver into the recess of the plug
upward until it's free.
1. Only use a 13 amp fuse.
cover and pull the fuse holder upward
3. Slide the fuse out and pop in the replacement.
2. To change the fuse, place a
until it's free.
screwdriver into the recess of the plug
4. Slot the fuse holder back into the recess and
cover and pull the fuse holder upward
push down until it locks into place.
3. Slide the fuse out and pop in the
until it's free.
replacement.
3. Slide the fuse out and pop in the
replacement.
4. Slot the fuse holder back into the
Replacing The Drive Belt
The drive belt is not included as spare part, contact Customer Service
helpline on the back page if a replacement is needed.
Check the drive belt carefully for wear, cuts and stressed areas. If the
drive belt appears worn, you will need to replace
it. To remove the drive belt, read the instructions
and follow the drawings below:
1. Grasp the old drive belt and remove from
motor shaft. Discard old drive belt.
2. Loop new drive belt over motor shaft and
stretch other end over floor brush in the
space provided between the bristles.
3. Place ends of floor brush down into slots on
sides as shown. Turn floor brush by hand
several times in the direction of the motor
3
shaft. If properly installed, drive belt will align
itself on floor brush.
4. Replace brush cover and
six screws.
3
Changing the fuse
1. Only use a 13 amp fuse.
2. To change the fuse, place a
screwdriver into the recess of the plug
cover and pull the fuse holder upward
2
until it's free.
3. Slide the fuse out and pop in the
replacement.
4. Slot the fuse holder back into the
recess and push down until it locks
into place.
14
1
2
1
4
2
3
4
Replace Brush
Cover and
Six Screws
3
USER MANUAL
1
2
4
Replace Brush
Replace Brush
Cover and
Cover and
Six Screws
Six Screws
15