Armytek Wizard PRO Kullanıcı Kılavuzu - Sayfa 2

Far Armytek Wizard PRO için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Armytek Wizard PRO 2 sayfaları.

Sayfayı Yazdır

Set description

Wizard

Depending on the model, your flashlight can inconsiderably differ from the pictures in the manual.

The producer reserves the right to change the package at his own discretion without modifying this manual.

Initial Service

The removable magnet in the tailcap.

With its help you can easily attach the flashlight to an electric service panel, a bike handlebar,

above a car wheel, etc.

The magnet can be taken out of the tailcap. To do this unscrew the small cover at the end of the

tailcap and put the magnet out.

Specifying the battery type for correct voltage indication.

Do not specify the type of power source manually unless you use unprotected Li-Ion batteries. 1x18650 Li-Ion battery is by default.

Press & Hold

Release after it will flash 3 times a second

OFF

Firefly1

Turbo1

Main3

Firefly2

Main2

Firefly3

Main1

To access the Menu press and hold the switch button (when the flashlight is switched off). It will switch on, go through the all available

modes, then after 2 seconds Turbo1 will access the Menu and will flash about 3 times a second. Release the button.

Now you can specify the battery type: 1 click for 1x18650 Li-Ion, 2 clicks for 2xCR123A, 3 clicks for 2xRCR123 Li-Ion.

To use the head mount with the flashlight:

Connect the

small strap

with the

silicone holder.

Fix the

flashlight and

adjust the

elastic bands

to the size

of your

head.

Items included in the package:

1 - Flashlight

6 - 2 spare O-rings

2 - Clip

7 - Magnet

3 - Lanyard

8 - Silicone holder

4 - Hand band

9 - User manual

5 - Headband (2 straps)

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the

head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

The flashlight is ready for operation.

Click x1, x2 or x3

1x18650 Li-Ion

2xCR123A

2xRCR123 Li-Ion

Pass the ends of the big strap through

the loop of the small strap and slots in

the silicone holder (fig.b), conjoin

them in a ring (fig.c). Pass the loose

end of the big strap through the loop of

the small one in the opposite direction

and fix it in the buckle (fig.d).

Main

The flashlight has 4 Sections of modes:

Click x2

Press & Hold

[Section1] – Firefly modes

OFF вMain

Main1 вMain2

[Section3] – Turbo modes

Main вFirefly

Main3

In OFF state:

Any mode вMain

Click: To turn on the last used mode.

Firefly

Click x2

Press & Hold

Press and hold: To turn on Firefly1 mode in [Section 1].

Firefly

OFF вFirefly

In ON state:

гд

Main

Firefly1 вFirefly2

Click: To turn off the flashlight.

Press and hold: To start cycling through the modes of the current Section.

Firefly3

The same in OFF & ON states:

Turbo

Click x3

Press & Hold

2 clicks: To turn on the Main mode [Section 2]. Then double clicks will switch

OFF вMax

Turbo1

modes between chosen modes in [Section 1] and [Section 2].

Any mode вMax

гд

Turbo2

3 clicks: To turn on Turbo mode [Section 3].

4 clicks: To turn on Special mode [Section 4].

Strobe

Click x4

Press & Hold

Wizard Pro has 2 types of operation:

Strobe1вStrobe2

OFF вStrobe

1. General. The flashlight is switched on/off by 1 click.

Any mode вStrobe

Strobe3

2. Tactical. The flashlight will switch on in the last used mode only for the time

the button is being pressed. This type of operation is useful for short-time

State Indication

Switching State Indication ON/OFF

lighting and setting signals.

Battery level

To access the Tactical operation type, unscrew the tailcap to 1/4, press the

< 100%

button and tighten the tailcap again keeping the button pressed.

< 50%

To return to the General type – press the button and keeping it pressed -

Press & Hold

5sec

unscrew the tailcap to 1/4.

Low Battery Indication

High Temperature Indication

Automemorizing. After switching off the last used Mode is memorized for

quick 1-click access at next switching on. If the flashlight was turned on in one

Warning

Critical

Warning

Critical

of the Special modes it will turn on in the last used Main mode.

Multicolor State Indication. Shows the battery level by short flashes every 5

seconds

dark.

2sec

1sec

2sec

1sec

Switching Multicolor State Indication ON/OFF. It is switched off by default in

< 25%

< 10%

WARM

HOT

OFF-state and Firefly modes. To turn on and off: unscrew the tailcap to 1/4,

press the button and holding the button pressed - tighten the tailcap and then unscrew it again. The settings will be memorized even

when battery is changed. Ultra-low current consumption allows color indication to work for more than 25 years.

Lock-out function. Unscrew the tailcap to 1/4 for the protection from accidental switching on. State Indication will be turned off.

Warning indication shows the battery level and the temperature inside the flashlight.

Low battery level. When it is < 25%, the color LED will show the warning level – flashing in orange color once in 2 second. With a further

voltage reducing brightness will start to decrease in steps for safety of the battery and user. If brightness will be <25% , the main LED

will flash 2 times. Critical battery level <10% is red indicated once a second.

High temperature. When it increases to the warning level – the color LED flashes by orange 3 times once in 2 seconds. At critical level

the color LED flashes in red 3 times a second, brightness starts to reduce. After cooling down the brightness increases to usual level.

Operation

[Section2] – Main modes

[Section4] – Special modes

even

in OFF state

. It also can be helpful to find the flashlight in the