Armytek Optoelectronics Viking PRO XHP50 Kullanıcı Kılavuzu - Sayfa 2

El feneri Armytek Optoelectronics Viking PRO XHP50 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Armytek Optoelectronics Viking PRO XHP50 2 sayfaları.
Ayrıca Armytek Optoelectronics Viking PRO XHP50 için: Kullanıcı Kılavuzu (2 sayfalar)

Sayfayı Yazdır

Set description

Viking

Items included in the package:

1 - Flashlight

5 - Holster

2 - Clip

6 - Spare rubber button

3 - Rubber grip

7 - 2 spare O-rings

4 - Lanyard

8 - User manual

Your flashlight can inconsiderably differ from the pictures in the manual.

The producer reserves the right to change the package at his own discretion without modifying this manual.

Initial Service

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

We DO NOT RECOMMEND to use low-quality CR123A batteries, because they can explode. Turbo mode needs

rechargeable 18650 Li-Ion batteries without PCB (unprotected) or with PCB which guarantees 7A discharge current

for stable work.

ь We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries can leak for various reasons

and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in then use new and high-

quality batteries and store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least once a

month. If you have noticed any signs of batteries' defects then withdraw them from the flashlight and utilize. It is also recommended to

replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.

Active temperature control. The flashlight can quickly heat up in Turbo mode. When the temperature becomes +60°C – the

brightness decreases by small steps. After cooling-down (provided that battery voltage is sufficient) the brightness increases to the

Turbo mode again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In conditions of good

air-cooling the flashlight delivers light without stepping down even in Turbo mode. There are no preset timers for stepping, but real-

time active temperature measurements.

Change Hunting/Tactical settings

Unscrew & Tighten up x10

x10

Constant light

Turbo

Tighten up

Click x1

Strobe

Additional modes

Click x1

Unscrew to 1/8

Cycling through Additional modes

Half Press & Release (no click)

Firefly1

1/2

Firefly2

Strobe

Main3

Main1

Main2

* if enabled

Change Constant modes

Unscrew & Tighten up

Turbo

гд

Main2

Change Strobe modes

Tighten up & Unscrew

Strobe2

гд

Strobe1

How to change Turbo1 & Turbo2

Half Press (no click) x15 & Click x1

1/2

x15

Low Battery Indication.

If the brightness is <25% from the nominal value, the LED flashes 2 times ONCE (after 30sec from switching

on). If you are not sure if it flashed or not switch the flashlight off and on: in case the battery is low flashes will repeat. Light output

decreases to Firefly mode at critical level.

Operation

Momentary on – any mode switched on by half-pressing of the

button (no click!) and active till the button is released. It is suitable

for giving signals by short button pressings. Click the button to

switch the light on permanently.

Hunting settings – comfortable modes for hunting. It's set by

default. Turbo mode (when the head is tightened up) and

Additional modes with constant light (changed by click with the

head unscrewed to 1/8). Remote switch can be used in Turbo.

Tactical settings – made for Special forces and Airsoft. Constant

light (when the head is tightened up) and Strobe mode (when the

head is unscrewed to 1/8). There are 2 Strobe modes and 2

Constant light modes for selection. Remote switch can be used in

ANY mode.

How to change the settings from one to another – unscrew and

tighten up the head of the flashlight at least 10 times (while

rotation you will change the modes). The pause must be <1 sec.

Hunting settings:

Turbo. Tighten the head of the flashlight if it is unscrewed. First full

click of the button turns the light on. Second full click turns it off.

Additional modes (2 Firefly + 3 Main + Strobe (if enabled)). If the

head of the flashlight is tightened up, unscrew it for 1/8 of a circle.

Full click of the button turns the light on at the last used Additional

mode.

Cycling through Additional modes. To switch the mode turn the

flashlight off and on (by full click or half-pressing). The modes

switch cyclically: Firefly1 – Firefly2 – Main1 – Main2 – Main3 –

Strobe (if enabled).

How to add/ remove Strobe in Additional modes. Switch on the

flashlight by half-pressing of the button at least 20 times. Last

switch should be clicked completely. The flashlight blinks,

confirming the action.

Tactical settings:

Constant light. Tighten the head of the flashlight if it is unscrewed.

First full click of the button turns constant light on. Second full

click turns it off. Also you can switch it on by half-pressing of the

button (no click).

Change Constant modes. The head is tightened up: unscrew it for

1/8 and tighten up again – Turbo and Main2 will switch cyclically.

Strobe. If the head is tightened up, unscrew it for 1/8 of a circle.

First full click of the button turns Strobe on. Second full click turns

it off. Also you can switch it on by half-pressing of the button (no

click).

Change Strobe modes. The head is unscrewed: tighten up and

unscrew it for 1/8 again – Strobe1 and Strobe2 will switch

cyclically.

How to set Turbo1 and Turbo2. Switch on the flashlight by quick

half-pressing of the button at least 15 times. Last switch should be

clicked completely. The flashlight blinks once (confirming the

selection of Turbo1) or 2 times (confirming the selection of

Turbo2).

Lock-out function. Unscrew the tailcap to 1/4 for the protection

from accidental switching on.

Automemorizing. After switching off the last used Mode is

memorized for quick 1-click access at next switching on.