Armytek Optoelectronics Wizard Pro Kullanıcı Kılavuzu - Sayfa 2

El feneri Armytek Optoelectronics Wizard Pro için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Armytek Optoelectronics Wizard Pro 2 sayfaları.
Ayrıca Armytek Optoelectronics Wizard Pro için: Kullanıcı Kılavuzu (2 sayfalar)

Sayfayı Yazdır

Set description

Wizard

Your flashlight can inconsiderably differ from the pictures in the manual.

The producer reserves the right to change the package at his own discretion without modifying this manual.

Initial Service

The removable magnet in the tailcap.

With its help you can easily attach the flashlight to an electric service panel, a bike handlebar,

above a car wheel, etc.

The magnet can be taken out of the tailcap. To do this unscrew the small cover at the end of the

tailcap and put the magnet out.

Specifying the battery type for correct voltage indication.

1x18650 Li-Ion battery is by default. Do not specify the type of power source manually unless you use 18650 Li-Ion batteries.

Press & Hold

Release while blinking 3 times/sec

OFF

Firefly1

Turbo1

Main3

Firefly2

Main2

Firefly3

Main1

To access the Menu press and hold the switch button (when the flashlight is switched off). It will switch on, go through 7 modes, then

after 2sec in Turbo1 mode – enter to Menu and flash about 3 times a second.

Now you can specify the battery type: 1 click for 1x18650 Li-Ion, 2 clicks for 2xCR123A, 3 clicks for 2x18350 or RCR123 Li-Ion.

After the choice is made the light will flash 1, 2 or 3 times to show the battery type chosen.

To use the head mount with the flashlight:

Connect the

small strap

with the

silicone holder.

Fix the

flashlight and

adjust the

elastic bands

to the size

of your

head.

Items included in the package:

1 - Flashlight

6 - 2 spare O-rings

2 - Clip

7 - Magnet

3 - Lanyard

8 - Silicone holder

4 - Hand band

9 - User manual

5 - Headband (2 straps)

To set/replace batteries:

1. Unscrew the tailcap.

2. Place the batteries with the positive contact (+) facing the

head of the flashlight.

3. Adjust the tailcap and tighten it as far as it can go.

The flashlight is ready for operation.

Click x1, x2 or x3

1x18650 Li-Ion

2xCR123A

2x18350 Li-Ion

2xRCR123 Li-Ion

Pass the ends of the big strap through

the loop of the small strap and slots in

the silicone holder (fig.b), conjoin

them in a ring (fig.c). Pass the loose

end of the big strap through the loop of

the small one in the opposite direction

and fix it in the buckle (fig.e).

Operation

Main

Click x2

Press & Hold

Main1 вMain2

Main вFirefly

Any State

Main

Main3

Firefly

Click x2

Press & Hold

OFF вFirefly1

Firefly

гд

Main

Firefly1 вFirefly2

Firefly3

Turbo

Click x3

Press & Hold

Any State

Turbo1

вTurbo

гд

Turbo2

Strobe

Click x4

Press & Hold

Any State

вStrobe

Strobe1 в Strobe2

Strobe3

Switching State Indication

Battery level

ON / OFF

< 100%

< 75%

5sec

Press & Hold

Low Battery Indication

High Temperature Indication

Warning

Critical

Warning

Critical

2sec

1sec

2sec

1sec

< 25%

< 10%

WARM

HOT

Constant light. Powerful electronics provide constant brightness even in the Turbo1 mode, using all energy of the battery. And the

Turbo2 mode gives the maximum brightness as the Overboost technology in cars, but until temperature of a flashlight and a discharge

current of the battery don't exceed critical values.

Active temperature control. The flashlight can heat up in Turbo mode quickly. When the temperature become +60°C – the brightness

decreases by small steps. After cooling-down (provided that battery voltage is sufficient) the brightness increases to the Turbo mode

again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In conditions of good air-cooling the

flashlight delivers light without stepping down even in Turbo mode. There are no preset timers for stepping, but real-time active

temperature measurements.

Digital Light Stabilization & Safe Soft-Start System monitors battery voltage, starts the flashlight at an admissible brightness or

decreases it by steps when the voltage dramatically fall down. These actions increase runtime, use all available energy, get longer

lifetime of rechargeable battery and protect it from overdischarge or overheating.

Warning indication shows the battery level and the temperature inside the flashlight.

Low battery level. When it is < 25%, the color LED will show the warning level – flashing in orange color once in 2 second. With a further

voltage reducing brightness will start to decrease in steps for safety of the battery and user. If brightness will be <25% from nominal

value, the main LED will flash 2 times. Critical battery level <10% is red indicated once a second.

High temperature. When it increases to the warning level – the color LED flashes by orange 3 times once in 2 seconds. At critical level –

it flashes by red 3 times once in 1 second, brightness starts to reduce. After cooling down the brightness increases to usual level.

The flashlight has 4 Sections of modes:

[Section1] – Firefly modes

[Section3] – Turbo modes

[Section2] – Main modes

[Section4] – Special modes

In OFF state:

Click: To turn on the last used mode.

Press and hold: To turn on Firefly1 mode in [Section 1].

In ON state:

Click: To turn off the flashlight.

Press and hold: To start cycling through the modes of actual Section.

The same in OFF & ON states:

2 clicks: To turn on the Main mode [Section 2]. Then double clicks will

switch modes between chosen modes in [Section 1] and [Section 2].

3 clicks: To turn on Turbo mode [Section 3].

4 clicks: To turn on Strobe mode [Section 4].

The flashlight has 2 types of operation:

1. General. The flashlight is switched on/off by 1 click.

2. Tactical. The flashlight will switch on in the last used mode only for

the time the button is being pressed. This type of operation is useful

for short-time lighting and setting signals.

To access the Tactical operation type, unscrew the tailcap to 1/4,

press the button and tighten the tailcap again keeping the button

pressed.

To return to the General type – press the button and while keeping it

pressed – unscrew the tailcap to 1/4.

Automemorizing. After switching off the last used Mode is memorized

for quick 1-click access at next switching on.

Lock-out function. Unscrew the tailcap to 1/4 for the protection from

accidental switching on. State Indication will be turned off.

Multicolor State Indication. Shows the battery level by short flashes

every 5 seconds

even

in OFF state

. It also can be helpful to find the

flashlight in the dark.

Switching Multicolor State Indication ON/OFF. It is switched off by

default in OFF-state and Firefly modes. To turn on and off: unscrew the

tailcap to 1/4, press the button and holding the button pressed –

tighten the tailcap and then unscrew it again. The settings will be

memorized even when battery is changed. Ultra-low current

consumption allows color indication to work for more than 25 years.