ARO 8212-1B series Operatör El Kitabı

Öğütücü ARO 8212-1B series için çevrimiçi göz atın veya pdf Operatör El Kitabı indirin. ARO 8212-1B series 7 sayfaları. 0 series

Sayfayı Yazdır
OPERATOR'S MANUAL
SECTION
M10
MANUAL
16
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
Released:
2/86
Revised:
1-20-95
"0" SERIES DIE GRINDER (SHORT GRINDER)
Form:
2884-2
Tool
Products
Models:
7015-11-(),
8212-1B-(
) and 8213-1B.
WARNING
READ THIS MANUAL
CAREFULLY
BEFORE
INSTALLING,
OPERATING
OR SERVICING
THIS EQUIPMENT.
FAILURE
TO OBSERVE
THE FOLLOWING
WARNINGS
COULD RESULT IN INJURY.
To aid the operator's
understanding
of proper and safe use of
l
grinders, the publications,
"Use, Care and Protection of Abrasive
Use only medium and high strength mounted wheels.
l
Wheels", A.N.S.I. 87.1, and "Safety Code for Portable Air Tools",
Do not use excessive
work pressure.
l
A.N.S.I. 8186.1, can be purchased
from:
Allow only people who have received training in "proper grind-
er operation" to operate grinder.
American National Standards Institute, Inc.
1430 Broadway
New York, New York 10018
l
Do not remove any labels. Replace any damaged label.
l
Use only accessories
recommended
by ARO.
l
l
l
l
l
l
l
l
l
l
l
Operate this tool at 90 p.s.i.g. (6.2 bar) maximum air pressure
at the air inlet of the tool.
Disconnect
air supply from tool before removing/installing
mounted wheel, mounted stone or performing other mainte-
nance procedures.
Keep hands, clothing and long hair away from rotating end of
tool.
Anticipate and be alert for sudden changes in motion during
start up and operation of any power tool.
Never exceed rated r.p.m. of tool.
Wear suitable eye and hearing protection while operating tool.
Tool shaft can continue to rotate briefly after throttle is re-
leased.
Do not lubricate tools with flammable or volatile
liquids such as
kerosene, diesel or jet fuel.
Use tool only for purposes for which it was intended.
Never use mounted stone or carbide burr with speed rating
lower than r.p.m. rating of tool.
Use only mounted wheels of the A, B and W shapes.
Repeated prolonged operator exposure to vibrations which may
be generated
in the use of certain hand-held
tools may produce
Raynaud's
phenomenon,
commonly
referred to as Whitefinger
disease.
The phenomenon
produces
numbness
and burning
sensations in the hand and may cause circulation and nerve dam-
age as well as tissue necrosis.
Repetitive
users of hand-held
tools who experience
vibrations
should closely monitor duration
of use and their physical condition.
The use of other than genuine ARO replacement
parts may
result in safety hazards, decreased
tool performance
and in-
creased maintenance
and may invalidate all warranties.
ARO is not responsible
for customer modification
of tools for
applications
on which ARO was not consulted.
Tool maintenance
and repair should be performed by autho-
rized, trained, competent
personnel.
Consult your nearest
ARO authorized
servicenter.
It is the responsibility
of the employer to place the information
in this manual into the hands of the operator.
For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand
Distribution
Center, White House, TN at PH: (615) 672-0321,
FAX: (615) 672-0601.
ARO Tool Products
Ingersoll-Rand
Company
1725 U.S. No. 1 North
l
P.O. Box 8000
l
Southern Pines, NC 28388-8000
01995
THE ARO CORPORATION
. PRINTED
IN USA.
Part of worldwide Ingersoll-Rand