Distech Controls LonWorks LonMark RCL-ITR Donanım Kurulum Kılavuzu

Kayıt Ekipmanları Distech Controls LonWorks LonMark RCL-ITR için çevrimiçi göz atın veya pdf Donanım Kurulum Kılavuzu indirin. Distech Controls LonWorks LonMark RCL-ITR 6 sayfaları. Certified room manager with interface and 4-channel rj9 inputs expander

Sayfayı Yazdır

LonMark

Product Description

This document describes the hardware installation procedures for the

RCL-ITR LonWorks Interface.

The Distech Controls RCL-ITR Room Manager and Network Interface

are designed to provide direct connectivity between Distech Controls™'

RJ9 accessories and the LON network. Moreover, the RCL-ITR

embeds four room controller LonMark objects, increasing lighting

and sunblind management capability to suit the most demanding

configuration requirements.

The RCL-ITR uses the LonTalk TP/FT-10 communication protocol and

is LonMark certified.

Figure 1-1:

RCL-ITR Enclosure

General Installation Requirements

For proper installation and subsequent operation of the module, pay

special attention to the following recommendations:

■

It is recommended that the module(s) be kept at room temperature

for at least 24 hours before installation to allow any condensation

that may have accumulated due to low temperature during

shipping/storage to evaporate.

■

Upon unpacking the product, inspect the contents of the carton for

shipping damages. Do not install damaged modules.

■

Avoid areas where corroding, deteriorating or explosive vapors,

fumes or gases may be present.

■

Allow for proper clearance around the module's enclosure, wiring

terminals and service pin to provide easy access for hardware

configuration and maintenance, and to ventilate heat generated

by the module. Remember to record the 12-character Neuron

located on either end of the module (shown on a sticker below the

barcode) for later commissioning.

■

Orient the module with the power supply terminal block connectors

towards the top to permit proper heat dissipation

www.distech-controls.com

Certified Room Manager with LonWorks

Hardware Installation Guide

Interface and 4-Channel RJ9 Inputs Expander

■

The module's datasheet specifies the power consumption, the

operating temperature range, and other environmental conditions

the module is designed to operate under.

■

Do not drop the module or subject it to physical shock.

■

If the module is used and/or installed in a manner not specified by

Distech Controls, the functionality and the protection provided by

the module may be impaired.

Any type of modification to any Distech Controls product

will void the product's warranty.

■

Take special care to connector positioning when wiring.

■

Before installing a Wireless Receiver, verify that local

communication regulations allow the installation of

wireless devices that operate at a frequency of 868 MHz.

Refer to the Open-to-Wireless

more information.

Take reasonable precautions to prevent electrostatic

discharges to the module when installing, servicing or

operating the module. Discharge accumulated static

electricity by touching one's hand to a securely grounded

object before working with the module.

Module Markings (Symbols)

Certain markings (symbols) can be found on the side of the module

and are defined as:

CE marking: conforms with the essential requirements of

the applicable EC directives.

Double Insulation Symbol: These modules are built with

double insulation.

Products must be disposed of at the end of their useful life

according to local regulations.

Read the notice.

For indoor use.

General Wiring Recommendations

Turn off power before any kind of servicing

■

All wiring must comply with electrical wiring diagrams as well as

national and local electrical codes.

■

To connect the wiring to a module, use the terminal connectors.

Use a small flat screwdriver to tighten the terminal connector

screws once the wires have been inserted (coupling torque: 0.5

Nm).

RCL-ITR

Solution Guide for

1/6