3Doodler 2.0 Hızlı Başlangıç Kılavuzu - Sayfa 2
Aksesuarlar 3Doodler 2.0 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. 3Doodler 2.0 2 sayfaları.
Ayrıca 3Doodler 2.0 için: Manuel (4 sayfalar), Kullanıcı Kılavuzu (10 sayfalar)
Sayfayı Yazdır
#WhatWillYouCreate?
TM
Troubleshooting
Guide
BEFORE YOU BEGIN, NOTE THE
FOLLOWING TIPS:
1. Use
PLA
LO/low
plastic on
ABS / FLEXY
HI/high
plastic on
(check the pack color)
2. It takes 30 - 40 seconds for extrusion to
begin after first inserting a plastic strand
3. Push the plastic down the pen and gently
twist it clockwise to get it to engage with the
pen's gears
4. Extrude all
ABS
plastic on
PLA
before switching to
plastic on
heat
How-to and help videos on our YouTube Channel:
YouTube.com/3Doodler
Still having issues?
If you are still having problems please message us at
(US) 718 618 9904
Please let us know what type of plastic you're using (ABS,
PLA or FLEXY)? What color is the LED on the pen once
warmed up?
Please also let us know the full serial number on the
underside of the pen.
heat setting, and
heat setting
HI/high
heat
LO/low
Remove the strand, snip
or call us at:
IS THE LIGHT
NO
TURNING ON?
IS THE PLUG WORKING?
YES
NO
WAIT TO FEED
It takes 30 - 40 seconds for
plastic to feed - either
press and hold the
extrusion button or double
click for continuous flow.
TWIST
Feed the plastic and gently
turn it a quarter clockwise,
ensuring the plastic is
gripped by the gears. If the
strand is too short, insert
another and push it
through.
PROBLEM SOLVED?
inserting PLA - wait for PLA to
YES
NO
TIGHTEN NOZZLE
SNIP & HEAT
The nozzle may be loose.
While the pen is hot (blue
the end and reinsert it.
or green LED), gently
Turn up the heat (temp
tighten the nozzle
adjustment) with mini
clockwise using the mini
screwdriver.
spanner included with your
pen. Don't apply
PROBLEM SOLVED?
excess force.
PROBLEM SOLVED?
YES
YES
NO
Use a spare power adapter
CORRECT POSITION?
to help determine if the
Ensure you are pushing
issue is with the pen or
the HI/LO switch to
the power cord.
the correct position.
YES
ARE YOU
SWITCHING FROM
NO
ABS TO PLA?
YES
ABS to PLA
Once you have decent flow,
Extrude all ABS on HI
switch to slow mode.
heat. Do this by keeping
the pen on HI heat, and
PROBLEM SOLVED?
start extruding before
switching to LO heat.
PROBLEM SOLVED?
YES
NO
NO
PAPER CLIP
Remove the nozzle then
get hold of the unblocking
tool or a paper clip that has
been straightened. Stick
the paper clip or
unblocking tool into the
front while continuing to
reverse.
PROBLEM SOLVED?
YES
Have Fun
Doodling!
SWITCH IN THE
YES
ISSUES WITH
SLOW
NO
MODE?
YES
Slow
Fast
USE FAST
YES
NO
NO
MAINTENANCE COVER
Try removing the maintenance
cover. Always press down on
the maintenance cover with
your thumb when removing/
inserting the metal bar. Ensure
the curve of the pin is facing
towards the pen when
inserted.
PROBLEM SOLVED?
YES