dji PHANTOM Hızlı Başlangıç Kılavuzu - Sayfa 6

Dronlar dji PHANTOM için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. dji PHANTOM 8 sayfaları. Led indicator description & faq
Ayrıca dji PHANTOM için: Hızlı Başlangıç Kılavuzu (17 sayfalar), Hızlı Başlangıç Kılavuzu (14 sayfalar), İleri Düzey Kılavuz (6 sayfalar), Hızlı Başlangıç Kılavuzu (3 sayfalar), Manuel (6 sayfalar), Hızlı Başlangıç Kılavuzu (3 sayfalar), Montaj (2 sayfalar)

Sayfayı Yazdır

Power on the Aircraft

1. Place the aircraft on the ground

2. Open the battery compartment cover of the aircraft.

3. Put the battery into the compartment with the power cord facing outward.

4. Connect the battery and aircraft by the power lead and make sure the ESC's work properly. (Correct sound)

5. Keep the sticks of the Transmitter and the Aircraft stationary until the system start and self-check has

finished(

6. Put the power cable into the battery compartment.

7. Close the battery compartment cover.

8. Please wait for the PHANTOM to warm up gradually (with the LED blinks Yellow 6 times quickly after the

Control mode LED blinks), since the built-in sensors need some time to reach a stable stage.

to fly the PHANTOM until the 6 rapid yellow flashes

 Please contact your dealer if the "System start and self-check LED flashes" are not correct (Red LED

appears in the last four green flashes) in the Step5.

 After power on and before the motors start-up, when the PHANTOM is stationary, if the LED blinks Green 6

times quickly after the Control mode LED blinks, please connect to the Assistant Software to do IMU basic

calibration by referring to the advanced manual. When the PHANTOM is moved, it is normal.

 After the system start and self-checking has finished, if the LED blinks Red, Yellow and Green continually,

that means the IMU data is abnormal. The PHANTOM will not work, please connect to the Assistant

Software and follow the tips to do operation. If it blinks red and yellow lights alternately (

means the compass error is too big, it can be caused by the following three cases:

1. There are ferromagnetic substance around; first make sure that the compass has been calibrated

correctly, you can lift the aircraft up (about 1m from the ground), and stay away from the surrounding

possible ferromagnetic material object, if there is no red and yellow flashing after lifting it up about 1m from

the ground, then it will not affect the flight.

2. The compass module had been put near a magnet; in this situation please timely replace the compass for

a new one, otherwise it will lead to some abnormal action, or even loss of control.

3. The compass is not properly calibrated; in this situation please calibrate the compass correctly again,

please see the GPS compass calibration for details.

Make sure not

disappear.

GPS & Compass Calibration

If the Compass Module is not used, you can skip this step.

The GPS module has a built-in magnetic field sensor for measuring the geomagnetic field, which is not the same

in different areas. The GPS module will not work unless the Compass Module has been connected. Make sure

the Compass Module connections are correct.

Please always keep the compass module away from the magnet. If this situation occurs please change the

compass module before flying. Otherwise it may damage the compass module and lead the aircraft to work

abnormally or even be out of control.

Calibrate the compass before the first flight or when flying in a different area.

ferromagnetic substance and other electronic equipment when calibrating or flying. If you keep having calibration

failure, it might suggest that there is magnetic interference or other ferromagnetic substance, please avoid flying

in this area.

1. Quickly switch the control mode switch from ATTI. Mode to GPS ATTI.

Mode and back to ATTI. Mode for 6 to 10 times, The LED indicator will

turn to constantly yellow.

2. Rotate your aircraft around the horizontal axis (about 360

changes to constant green, and then go to the next step.

3. Hold your aircraft vertically and rotate it (its nose is downward) around the

vertical axis (about 360

is finished.

4. The LED indicator will show whether the calibration was successful or

not.

 If the calibration was successful, calibration mode will exit automatically.

 If the LED keeps flashing quickly Red, the calibration has failed. Switch

the control mode switch one time to cancel the calibration, and then

re-start from step 1.

), that

Horizontal Rotation

11 |

) until the LED

) until the LED turns off, meaning the calibration

Make sure to keep away from

GPS ATTI. Mode

ATTI. Mode

ATTI. Mode->GPS ATTI. Mode

-> ATTI. Mode is one time，

quickly switch 6 to 10 times

Vertical Rotation

12 |