djm direct DJMSL10 Orijinal Kullanım Kılavuzunun Çevirisi - Sayfa 8
Testere djm direct DJMSL10 için çevrimiçi göz atın veya pdf Orijinal Kullanım Kılavuzunun Çevirisi indirin. djm direct DJMSL10 14 sayfaları. 10 single bevel compound sliding mitle saw
Sayfayı Yazdır
Setting the fence square with the table
1. Make sure that the electrical plug is removed from the power
point.
2. Push the saw arm (1) down to its lowest position and engage the
release knob (2) to hold the saw arm in the transport position.
3. Loosen the mitre locks (18) and lifting up the mitre latch (19).
4. Rotate the table (14) until the pointer is positioned at 0°.
5. Release mitre latch (19) and tighten the mitre locks (18).
6. Using a 5 mm hex key, loosen the two screws securing the fence
(12) to the base.
7. Place a square against the fence (12)and alongside the blade.
8. Adjust the fence (12) until it is square with the blade.
9. Tighten the screws securing the fence (12).
10. Loosen the Phillips head screw holding the pointer of the mitre
scale (15) and adjust it so that it accurately indicates the zero
position on the mitre scale.
11. Retighten the screw securing the mitre scale pointer.
Changing a blade
1. Make sure that the electrical plug is removed from the power
point.
2. Push down on the operating handle (3) and pull the release knob
(2) to disengage the saw arm (1).
3. Raise the saw arm (1) to its highest position.
4. Loosen the cover plate screw about 2 turns with a Phillips
screwdriver. Do not remove this screw from the tool.
5. Pull the rotating blade guard (6) down. When the rotating blade
guard (6) is positioned over the upper fixed blade guard (4) it is
possible to access the blade bolt.
6. Lift and hold up the lower blade guard (6) to expose the threaded
blade bolt.
7. Hold the rotating guard (6) up and press the spindle lock button
(20). Rotate the blade until the spindle locks.
8. Use the 6 mm hex key provided to loosen and remove the blade
bolt. (Loosen in a clockwise direction as the blade screw has a left
hand thread).
9. Remove the flat washer, outer blade washer and the blade.
10. Wipe a drop of oil onto the inner blade washer and the outer
blade washer where they contact the blade.
11. Fit the new blade onto the spindle taking care that the inner
blade washer sits behind the blade.
12. Replace the outer blade washer.
13. Depress the spindle lock button (20) and replace the flat washer
and blade bolt.
14. Use the 6 mm hex key to tighten the blade bolt securely (tighten
in an anti-clockwise direction).
15. Lower the blade guard, hold the rotating lower blade guard (6)
and blade bolt cover (8) in position and tighten the fixing screw to
secure the blade bolt cover in position.
16. Check that the blade guard operates correctly and covers the
blade as the saw arm is lowered.
17. Connect the saw to the power supply and run the blade to make
certain that it is operating correctly.
Cross cut
If possible, always use a clamping device such as a 'G" clamp to
secure your workpiece.
When cutting your workpiece, keep your hands well away from the
blade area.
Do not remove a cut-off piece on the right-hand side of the blade
using your left hand.
A crosscut is made by cutting across the grain of the workpiece. A
90°crosscut is made with the mitre table set at 0°. Mitre crosscuts are
made with the table set at some angle other than zero.
1. Pull on the release knob (2) and lift the saw arm (1) to its full
height.
2. Loosen the mitre locks (18) and lifting up the mitre latch(19) .
3. Rotate the mitre table (14) until the pointer aligns with the desired
angle.
4. Release mitre latch(19) and retighten the mitre locks (18).
5. Place the workpiece flat on the table with one edge securely
against the fence (12). If the board is warped, place the convex side
against the fence (12). If the concave side is placed against the fence,
the board could break and jam the blade.
6. When cutting long pieces of timber, support the opposite end of
the timber with side support bars, a roller stand or a work surface
that is level with the saw table.
7. Before turning on the saw, perform a dry run of the
cutting operation to check that there are no problems such as a
clamp interfering with the cutting action.
8. Hold the operating handle (3) firmly and squeeze the switch trigger
(17). Allow the blade to reach maximum speed and slowly lower the
blade into and through the workpiece.
9. Release the switch trigger (17) and allow the saw blade to stop
rotating before raising the blade out of the workpiece. Wait until the
blade stops before removing the workpiece.
Bevel cut
If possible, always use a clamping device such as a 'G" clamp to
secure your workpiece.
When cutting your workpiece, keep your hands well away from the
blade area.
Do not remove a cut-off piece on the right-hand side of the blade
using your left hand.
7