Altronix HubSat42Di Kurulum Kılavuzu - Sayfa 4
Anahtar Altronix HubSat42Di için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Altronix HubSat42Di 8 sayfaları. Passive utp transceiver hub with integral isolated camera power
Ayrıca Altronix HubSat42Di için: Kurulum Kılavuzu (12 sayfalar)
Sayfayı Yazdır
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6) power
LEDs (Green) of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv
or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).
4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to insure proper operation and avoid possible damage.
5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).
6. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs
of cameras (Figs. 2a-2d, pg. 6). Polarity must be observed.
•
HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 6).
•
HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 6).
7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners
to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 6). Polarity must be observed.
When using fixed cameras disregard this step.
8. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the
BNC video outputs of cameras (Figs. 2b-2d, pg. 6).
9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6).
Fig. 1 - HubSat4Di Circuit Board
1b - Output
PTCs: Protects
each output.
1a - BNC
Connector: Video
in from remote
camera video
out to DVR.
1i - Channels 1-4:
CAT-5 or higher
structured cable
to cameras.
1h - Data: CAT-5 or higher structured
cable to data port on HubWay8/16, HubWayLD8/16,
HubWayLDH8/16 or head end equipment (DVR).
- 4 -
1c - Power Terminals: 24VAC/28VAC power outputs.
28VAC
AUX1
AUX2
24VAC
VIDEO1
PVD1
PVD2
28VAC
28VAC
AUX3
24VAC
24VAC
VIDEO2
VIDEO3
DATA 1-4
VIDEO 1-4
PVD3
1g - Channels 1-4: Single CAT-5 or higher
structured cable out to HubWay8/16, HubWayLD8/16,
HubWayLDH8/16 enables transmission
of up to four (4) video signals.
1d - Output
Voltage Switches:
Selects
24VAC/28VAC/OFF
28VAC
AUX4
for each output.
24VAC
VIDEO4
PVD4
1e - LED(s) 1-4:
Power output
indicators.
1f - Data:
RS422/RS485
input from head
end equipment
(DVR) for PTZ
control.
HubSat4Di