Altronix HubSat8D Kurulum Kılavuzu - Sayfa 4

Anahtar Altronix HubSat8D için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Altronix HubSat8D 8 sayfaları. Passive utp transceiver hub with integral camera power eight (8) channel passive utp transceiver hub with integral camera power eight (8) channel passive utp transceiver includes eight (8) hubwayav video balun/combiners eight (8) channel passive utp

Sayfayı Yazdır

2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1]

on Circuit Board A (Fig. 1i, pg. 4). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured

cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.

•

For 24VAC cameras use Altronix model HubWayAv Video Balun/Combiner (Figs. 2a, 2b, pg. 6).

•

For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

•

For non-isolated 12VDC cameras use Altronix model HubWayDvi Video Balun/Combiner (Figs. 2c, 2d, pg. 6).

The total cable distance must not exceed 750 ft. for video transmission between the HubSat8D and each camera.

Repeat this step for all other camera channels [PVD2-4] on Circuit Board A and [PVD1-4] on Circuit Board B.

3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6) power

LEDs (Green) of the HubSat8D will illuminate when AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv

or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).

4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to

each camera to insure proper operation and avoid possible damage.

5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 6).

6. Connect power outputs of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to power inputs

of cameras (Figs. 2a-2d, pg. 6). Polarity must be observed.

•

HubWayAv - Terminals marked [AC POWER] (Figs. 2a, 2b, pg. 6).

•

HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 6).

7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners

to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 6). Polarity must be observed.

When using fixed cameras disregard this step.

8. Connect the BNC connector of HubWayAv, HubWayDv or HubWayDvi Video Balun/Combiners to the

BNC video outputs of cameras (Figs. 2b-2d, pg. 6).

9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 6).

Fig. 1 - HubSat Circuit Board A / HubSat Circuit Board B

VIDEO1

1a - BNC Connector: Video in from remote camera

video out to DVR.

1b - Output PTCs: Protects each output.

1c - Power Terminals: 24VAC/28VAC power outputs.

1d - Output Voltage Switches: Selects

24VAC/28VAC/OFF for each output.

1e - LED(s) 1-4: Power output indicators.

1f - Data: RS422/RS485 input from head end equipment

(DVR) for PTZ control.

- 4 -

28VAC

AUX1

AUX2

24VAC

PVD1

PVD2

28VAC

24VAC

VIDEO2

VIDEO3

DATA 1-4

VIDEO 1-4

1g - Channels 1-4: Single CAT-5 or higher structured

cable out to HubWay, HubWayLD or HubWayLDH enables

transmission of up to four (4) video signals.

1h - Data: CAT-5 or higher structured cable to data port

on HubWay, HubWayLD or HubWayLDH or head end

equipment (DVR).

1i - Channels 1-4: CAT-5 or higher structured cable

to cameras.

28VAC

AUX3

AUX4

24VAC

VIDEO4

PVD3

PVD4

HubSat8D