Custom Dynamics MAGIC-STROBES-HD Kurulum Talimatları

Motosiklet Aksesuarları Custom Dynamics MAGIC-STROBES-HD için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Custom Dynamics MAGIC-STROBES-HD 2 sayfaları. Brake flasher
Ayrıca Custom Dynamics MAGIC-STROBES-HD için: Kurulum Talimatları (2 sayfalar)

Sayfayı Yazdır

Part Number: MAGIC-STROBES-HD

Package Contents:

- Magic Strobes™ Brake Flasher (1)

- Tie Wraps (5)

'96-'10 Softails (except Convertible, Rocker and Breakout), '97-'11

Dynas, '97-'13 Touring (Except '10-'13 Street Glide/Road Glide Cus-

tom), '99-'03 Sportsters, '10-'13 HD Trikes; '11-'13 Road Glide Ultra

Installation

1. Secure motorcycle on level surface.

2. Remove seat or side panel, depending on

model.

3. Disconnect negative [ - ] battery cable from

the battery.

4. Locate and unplug the lighting connector to the

rear fender.

5. Plug the Magic Strobes™ Module, in-line, into

the rear lighting harness and into the bike's

wiring harness.

6. Re-connect the battery's negative battery

cable to the negative [ - ] of the battery.

7. Select Desired Pattern on the dial with power

Off. (See page 2 for Pattern Information)

8. Check Operation.

9. To change pattern, turn bike OFF and change

dial to desired pattern.

10. Locate a secure place for the Magic Strobes™

unit that will not interfere with the secure

placement of the seat. Secure with the en-

closed tie-wraps so that unit will not move.

Questions? Call us at: 1 (800) 382-1388

Custom Dynamics® Magic Strobes™ Brake Flasher

Installation Instructions

We thank you for purchasing the Custom Dynamics® Magic Strobes

Brake Light Flasher! Our products utilize the latest technology and

high quality components to ensure you the most reliable service. We

offer one of the best warranty programs in the industry and we back

our products with excellent customer support, if you have questions

before or during installation of this product please call Custom

Dynamics® at 1(800) 382-1388.

Important: Module must be secured after installation.

Find safe area away from any moving parts and out of the

way of normal operation of the bike. Use the enclosed tie-

wraps to secure. Custom Dynamics® is not liable for damage

as a result of improperly securing or failing to secure the

module.

Note: When using a Magic Strobe™ with a Signal Stabi-

lizer™ or other Load Equalizer we recommend to install the

Magic Brake Strobe™ after (towards the taillight) the Signal

Stabilizer or Load Equalizer. (See Diagram)

Note: When using a Magic Brake Strobe™ with a Run-

Brake-Turn Controller, we recommend the following:

-To flash Brake and turns, Install Magic Strobe™ Before Run-

Brake-Turn Controller. (See Diagram)

-To flash only the center taillight, install Magic Strobe™ After

Run-Brake-Turn Controller. (See Diagram)

Important: Customers using this module with standard

incandescent bulbs should use patterns 0-3 only. Any other

settings selected will result in diminished performance.

Caution: A stuck brake switch may cause this unit to

overheat and fail . Unplug module immediately if this condi-

tion occurs.

Note: Although this device has been designed to significantly in-

crease your braking visibility, flash/strobe patterns may not be street

M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST

ATTENTION

Please read all Information below before Installation

legal in your area. This Device is not DOT approved.

08-2015SM