CustomWorks NITRO ROCKET KIT 0715 Manuel - Sayfa 13

Motorlu Oyuncak Araba CustomWorks NITRO ROCKET KIT 0715 için çevrimiçi göz atın veya pdf Manuel indirin. CustomWorks NITRO ROCKET KIT 0715 16 sayfaları.

Sayfayı Yazdır

Tire Bag

Tire & Wheel Installation

-Parts for

Bag M

6204

Qty 2

Street-Trac FRONT

NOTE:

In this step you will be using a fast drying super glue type adhesive to

NOTE:

NOTE: In this step you will be using a fast drying super glue type adhesive to

NOTE:

In this step you will be using a fast drying super glue type adhesive to

secure the tires and wheels to each other. Be very careful with this process as

the glue can tend to run very easilly through the tire and may glue your

finger to the tire or wheel before you know it. You must follow the directions

and precautions provided by the glue manufacturer to insure a secure bond.

STEP #1:

STEP #1: Using a reamer or a small drill bit make a hole in the

STEP #1:

center of each of the 4 wheels as shown in Figure 1.

STEP #2: Place the foam inserts into the tires with the wider

STEP #2:

inserts going in the rear tires, the narrower in the fronts. Make

sure the insert is laid into the tire evenly. As shown in Figure 2

it should not be bunched up too much in any area.

STEP #3:

STEP #3: Place the wheel inside of the tire and work both

STEP #3:

beads of the tire into the channels on the outside edge of the

wheel. Peel back a portion of the tire from the wheel and

apply an even bead of tire glue between the wheel and the

tire as shown in Figure 3.

Figure 3.

Figure 3. It may be easiest to only glue one

Figure 3.

section at a time, rather the entire bead at once. Also

wrapping electrical tape around the edge of the tire will help

hold the tire tight to the wheel as the glue sets. Repeat this

step several times working your way around the tire until it is

secure.

You may repeat this process now for the remaining 3 tires

BUT BE SURE TO PLACE THE FRESHLY GLUED SIDE UP

BUT BE SURE TO PLACE THE FRESHLY GLUED SIDE UP until it

BUT BE SURE TO PLACE THE FRESHLY GLUED SIDE UP

has dried completely. Once dry it is a good idea to go back

and re-seal the edges by applying another small bead of glue

and letting it run around the edge of the tire at the gap

between tire and wheel.

STEP #4:

STEP #4: Place one #1226 Bearing into each side of the front

wheels as shown in Figure 4.

Figure 4.

STEP #5:

STEP #5: Refer to Figure 5

Figure 5

Figure 5 and place one 7047 shim over the front axle followed by the front wheel and then

STEP #5:

Figure 5

the 7220 Axle Spacer. Now secure with one 5207 Locknut, be very careful to not overtighten the nut. You

want to tighten it just enough to eliminate any slop from side to side but no more. Repeat for other side of car.

STEP #6:

STEP #6: Now slide one of the rear wheels onto the rear axle as shown in Figure 6.

STEP #6:

axle so that it slides into the drive slot molded in the back of the wheel. Secure with a 5207 locknut. Wheel should

spin freely, remove 7047 spacers from behind roll pin if necessary. Do not overtighten 5207 nut.

TIRE TIPS:

- The tires work best after a run or two of breaking in depending on the dirt oval track surface. Lightly scuffing the

tires on asphalt (1min of gentle driving) helps break them very quickly.

- Cleaning the tires with Simple Green and a rag works very well and gives the tire a little more grip.

- Traction additives such as Paragon or Buggy Grip also help with traction but will not cure ill-handling issues. If you

do not have these products, applying WD-40 to the tire can do wonders as well.

6214

Qty 2

6220

Qty 2

Street-Trac REAR

Soft Insert FRONT

Figure 1.

6221

Qty 2

6252

Qty 2

Soft Insert REAR

Front Wheel

Figure 2

Figure 1

Figure

Figure 5

5207

Qty 4

8-32 Lock Nut

6253

Qty 2

1226

Rear Wheel

Ball Bearing

Figure 2

Figure 4

Figure 6

Figure 6.

Figure 6. Be sure to index the roll pin in the

Figure 6.

1:1

7047

Qty 6

Spacer

1:1

Qty 4

7220

Qty 2

Axle Spacer