artograph EZ Tracer Kullanıcı Kılavuzu

Projektör artograph EZ Tracer için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. artograph EZ Tracer 4 sayfaları.

Sayfayı Yazdır

EZ Tracer Projector

User's Guide

Thank You...

for purchasing Artograph's

EZ Tracer Projector. Quickly and easily enlarge

(up to ﬁ ve times) and trace your projects. We hope

you enjoy your new EZ Tracer! If you have any

questions or suggestions, please contact us

toll-free at 1-888-975-9555, or send an email

to [email protected].

ELECTRICALLY-OPERATED PRODUCT.

FOR USE BY AGES 15 AND UP.

PLEASE SAVE THESE INSTRUCTIONS

Important Safety Instructions

When using your projector, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Close supervision is necessary when any projector

is used by or near children. Do not leave projector

unattended while in use.

3. Care must be taken as burns can occur from

touching hot parts.

4. The projector on and off switch is located at the

back of the unit

5. Do not operate projector with a damaged cord or if

the projector has been dropped or damaged –

until it has been examined by a qualiﬁ ed serviceman.

6. Position the cord so that it will not be tripped over,

pulled, or contact hot surfaces.

7. If an extension cord is necessary, a cord with a

current rating at least equal to that of the projector

should be used. Cords rated for less amperage than

the projector may overheat.

8. Always unplug projector from electrical outlet before

cleaning and servicing and when not in use. Never

yank cord to pull plug from outlet. Grasp plug and

pull to disconnect.

9. Let projector cool completely before putting away.

Loop cord loosely around projector when storing.

10. To reduce the risk of electric shock, do not immerse

this projector in water or other liquids.

11. To reduce the risk of electric shock, do not

disassemble this projector, but take it to a qualiﬁ ed

serviceman when service or repair work is required.

Incorrect reassembly can cause electric shock when

the projector is used subsequently.

12. The use of an accessory attachment not

recommended by the manufacturer may cause a

risk of ﬁ re, electric shock, or injury to persons.

13. Connect this projector to a grounded outlet.

14. Disconnect this unit from its source of supply before

replacing the projection lamp.

15. This projector has a polarized plug (one blade is

wider than the other). To reduce the risk of electric

shock, this plug is intended to ﬁ t in a polarized

outlet only one way. If the plug does not ﬁ t fully in

the outlet, reverse the plug. If it still does not ﬁ t,

contact a qualiﬁ ed electrician. Do not modify the

plug in any way.

Set up & Operation

1. Install Lamp

EZ Tracer requires an incandescent (75 watt max) lamp

or 15 watt compact ﬂ uorescent (recommended) lamp

(not included).

2. Room Lighting

All opaque projectors work like a ﬂ ashlight; the darker the

room, the brighter the projected image will appear. For

best results, operate your EZ Tracer in a room where you

are able to control the lighting conditions.

3. Projecting the Image

CAUTION: Photographs or resin-coated prints may

not be used with the EZ Tracer. Photographs may

be adversely affected by the heat and light.

1. Lay the art or design face-up on a ﬂ at hard surface.

CAUTION: Do not put the projector on a soft or heat

sensitive surface, as damage may occur.

WARNING: The EZ Tracer must be positioned near

an electrical outlet. Carefully arrange the cord

so that it won't be tripped over or pulled while

projecting in a dark room.

2. Place the EZ Tracer on top of the art or design with the

opening at the bottom of the projector positioned over

the area you wish to project.

3. Plug the EZ Tracer into an electrical outlet and turn the

black switch on.

4. Turn off any room lights and point the EZ Tracer

toward the desired wall or vertical surface

(i.e. easel, canvas etc.).

3. Sizing and Focusing

To change the size of the projected image, move the EZ

Tracer either closer to the projection surface for a smaller

enlargement, or farther away for a greater enlargement.

Focus by sliding the lens barrel in or out.

Tips & Techniques

Projecting Oversized Copy

To project artwork larger than the display area, project the

image in sections or reduce original on a copier.

#306-264