Alula RE614-Au Hızlı Başlangıç Kılavuzu - Sayfa 2

Duman Alarmı Alula RE614-Au için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Alula RE614-Au 13 sayfaları. Smoke alarm connect+ encrypted

Sayfayı Yazdır

Normal Operation

Power Up

Standby

Sensing Fire

Fault Mode

Low Battery

Faulty Smoke Sensor

End of Life

Silence Sounding

Alarm

Silence "End of Life"

indication (up to

30 days)

Test Mode

Test Smoke Alarm

Alarm Memory

24 Hour Memory

Long Term Memory

1.1. Normal Operation

1.1.1. Power Up

Twist off the Alarm from the mounting plate.

The red LED will flash once followed by one flash

of the yellow LED to indicate that the Alarm

has been powered successfully and is now in

standby mode.

1.1.2. Standby

In standby mode there are no active visible or

audible indications which can be intrusive to

the householder. To confirm that the Alarm is

operational perform a weekly button test.

1.1.3. Weekly button test

Press and hold the test button and verify that

the red LED flashes rapidly and the Alarm

ramps up to full sound.

1.1.4. Sensing Fire

As soon as the Alarm senses smoke it will

go into Alarm. The red LED on the Alarm

sensing smoke flashes rapidly to indicate this

is the Alarm sensing smoke / fire. Follow the

instruction in section 3 and evacuate the

building.

1.1.5. Silence False / Nuisance alarm

Occasionally Smoke Alarms can be activated

by phenomena other than fire, e.g. dust,

insects, cooking fumes. Once you are sure it is

a nuisance alarm press the large test button to

silence the Alarm for 10 minutes – the red LED

will then flash every 8 seconds for 10 minutes.

1.1.6. Nuisance alarm

In the case of a real fire, the occupiers of the

dwelling should proceed to evacuate as per

instructions in section 3. However if the system

RE614-Au Indicator Summary

Action

Twist on Base

Action

Press & Release Button

Action

Press Button

Action

Press & Hold Button

Red LED

1 Flash

Off

Rapid Flashing

Off

Red LED

Off

1 Flash every 48 sec

Off

2 Flashes every 48 sec

Off

3 Flashes every 48 sec

1 Flash every 8 sec

Off

Off for 72 hours

Red LED

Rapid Flashing

Off

Red Led

2 Flashes every 48

Off

sec for 24 hours

Rapid Flashing

Off

is responding to a recurring nuisance alarm it

is very important that the offending Alarm is

identified so the problem can be eliminated by

cleaning or replacing this Alarm. The offending

Alarm can be identified by a rapidly flashing

red LED. Once the offending Alarm has been

located follow 1.1.5 above.

1.2. Fault Conditions

1.2.1. Low battery

The Alarm will emit a short beep and flash the

Yellow LED when it becomes partially depleted.

Check the date when the Alarm should be

replaced which is given on the sidewall of the

Alarm. When electronic self testing indicates

that the battery is becoming low the Alarm will

beep and the yellow LED will flash at the same

time (about every 48 seconds) to warn the

user. This indicates that the battery or batteries

must be replaced.

1.2.2. Contaminated chamber

If the Alarm sounds without any apparent

smoke being present, press the test button to

silence the Alarm for 10 minutes (as described

in 1.1.5 above). If the Alarm sounds again

it may be contaminated. Pressing the test

button again, within 4 minutes of the Alarm

re-sounding, will get the Alarm to compensate

for chamber contamination. This will normally

resolve the problem.

If the Alarm re-sounds for a third time, the

Alarm is excessively contaminated and must

be replaced. If it is not convenient to replace

it immediately, pressing the test button within

4 minutes of it going into alarm (for the third

Yellow LED

Off

Full Sound

Yellow LED

1 Beep

2 Beeps

3 Beeps

Off for 10 mins

Off for 72 hours

Yellow LED

Full Sound

Yellow LED

Off

Rapid Chirping

Sounder