ALUZ ZIZA Manuel

Aydınlatma Ekipmanları ALUZ ZIZA için çevrimiçi göz atın veya pdf Manuel indirin. ALUZ ZIZA 14 sayfaları. Led tape

Sayfayı Yazdır
Surface Mount LED
(Included)
Adhesive Backing
(Included)
GENERAL FEATURES
Applications
Accent, Decorative, Surface, Recessed, Pendant Lighting
Viewing Angle
120°
Length
Built to Order (+/- 1/8" Tolerance)
Construction
Flexible LED Tape
Assembly Increment
4"
Field Cutting
Dry Location Only
Weight
0.016 lbs per foot
Mounting
Mounting Channel or Mounting Clips (Sold Separately)
Dry or Wet (IP67) Location
Listing
UL2108, 67.1.9, 60.4, CSA C22.2 #9
UL8750, CSA250
Driver
Remote (Sold Separately)
Operating / Startup: -20° to 48°C (-4° to 120°F)
Temperature Ratings
Storage: -40° to 76°C (-40° to 170°F)
Installation Link
ELECTRICAL
Dimming
DMX
21' (5.5W)
Maximum Run
26' (4.5W)
(Class 1 Applications)
15' (5.5W)
Maximum Run
18' (4.5W)
(Class 2 Applications)
Luminaire Voltage
24VDC
1170 N Red Gum St, Anaheim, CA 92806
aluz.lighting
© ALUZ All Rights Reserved. ALUZ reserves the right to make changes or withdraw specifi cations without prior notice.
A8 Series | LED Tape
ZIZA Tape
(A8-ZIZA-TAPE)
LED Lightstrip
1.5 Minimum Bend Radius
(A8-ZIZA-TAPE)
Dry Power Connector
20/5 Gauge Wire
(A8-PC-5P-DRY)
866.ALUZ.LTG | 714.535.7900
READ ENTIRE GUIDE BEFORE STARTING INSTALLATION
Important Notice: Verify correct luminaire was received with correct
color temperature, voltage, and wattage before cutting or installing.
ALUZ will not be responsible if incorrect luminaire is installed.
END VIEWS / DIMENSIONS
.75"
.46"
.09"
Dry Location
Wet Location
PRODUCT INFORMATION
• For accent, decorative, surface, recessed, or pendant lighting.
• 24 Volts DC for easy and safe installation.
• Long life, energy effi cient LEDs.
• Can be ordered to specifi c lengths for when exact dimensions are known
Example: 10 x 10'6"
• Plug and light system.
• Lead wires are typically 36" long and exit on one end.
ELECTRICAL REQUIREMENTS
• Luminaires require a 24 Volt DC remote driver.
• To calculate driver size, determine Watts per Foot.
Example: 4.5W per Foot
• Determine Length in Feet.
Example: 10'
• Calculate Load: Multiply Watts per Foot x Length in Feet
Example: 4.5W x 10'= 45W
• Choose a driver from catalog.
Example: 60 Watt Driver
• Determine maximum driver distance using Maximum Wire Length Table on
drivers page.
Example: 45 watts is between 40W and 60W. Using #14 wire, maximum distance
is 37' from driver to fi rst LED.
INSTALLATION RECOMMENDATIONS
• Luminaires must be mechanically attached directly to mounting surface using
mounting clips, channels, or other appropriate means.
Refer to installation step by step pages for details.
• Conduit raceway should be sleeved at one end for low voltage wires going to driver.
INSTALLATION TOOLS REQUIRED
• Electric Hammer Drill
• 14.4 to 28 Volt Cordless Drill
• Phillips Bits
• Utility Knife
• Electrical Cord
• Marker
• Wire Stripper
Page 1 of 13
Overview
.78"
• Long Nose Pliers
• Drill Bits - Concrete or Wood
• Electrical Three Ways
• Safety Glasses
• Measuring Tape
• Laser Line or Chalk Line
Installation Instructions
8 / 11 / 2023 / Rev 2