1-CUBE SU 6.2. Kullanıcı Kılavuzu - Sayfa 8

Termostat 1-CUBE SU 6.2. için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. 1-CUBE SU 6.2. 13 sayfaları. Water thermostat

Adjustment of the required temperature or time:

The required temperature or time in the methods (menu) THERMOSTAT, CALIBRATION and PROFILE are adjusted by

pressing keys plus + (to increase the value) or minus – (to decrease the value). First the required value is changed of

tenths of degree or 1 seconds, after ten changes (ten presses of key) the required value is changed of degrees or 10

seconds, after ten following changes (ten presses of key) the required value is changed of 10 degrees or 100 seconds

etc. Once you have adjusted the required data push the key OFF to save it into the memory, after this step the text

THERMOSTAT appears again on the display.

Method Thermostat:

This algorithm allows to adjust any required temperature and the Water Bath maintains the temperature for the

required time. The device has saved the last value adjusted temperature that was regulated. If you do not want to

change the value of the temperature start the algorithm itself by pressing the key ON. The text: REQ.CONTROL:

appears on the first line of the display, there is the time in minutes „min="and the real temperature „T=" in

on the

second line.

If the set temperature doesn't suit you and you need to change it you have to adjust the required temperature before

you press the key ON. The required temperature is set with the help of keys plus + (to increase the value) or minus –

(to decrease the value) – see the paragraph above: Adjustment of the required temperature or time: in the chapter

Control algorithms. After setting the required temperature press the key OFF and in that way the required

temperature is saved and the text THERMOSTAT appears again on the display. Now you can start the temperature

control running by pressing the key ON. The algorithm is stopped by pressing the key OFF. If there is not enough

water in the Bath the text „add water" appears automatically on the display and it will disappear once the water is

added.

Method PROFILE:

This algorithm allows to adjust any required time behaviour of temperatures. It is possible to adjust as many as 7

points defined with time and temperature coordinates. After choice of the item PROFILE in the main menu with the

help of the key ROTATION one can start the algorithm itself by pressing the key ON.

After 1 sec the text: START ON:

OTHER PARAMETERS: appears on the display.

If there has been already set the temperature curve before, one can use it again (because it is saved in the internal

memory) by holding the key ON at the time when the text: START ON:

OTHER PARAMETERS: appears on the display.

If there hasn't been set the temperature curve yet or it is necesary to set it in a different way, one waits about 1 sec

till the text SET UP THE CURVE appears on the display. After that the text: time of point 1= appears on the first line and

one sets the time in minutes on the second line. Time is set with the help of keys plus + (to increase the value) or

minus – (to decrease the value) – see paragraph: Adjustment of the required temperature or time: in the chapter

Control algorithms. After setting the time of point 1 press the key OFF and in that way time of point 1 is saved in the

internal memory and after that the text: time of point 2= appears on the first line and one sets in the same way the

time of point 2, the time of point 3, the time of point 4, the time of point 5, the time of point 6, the time of point 7.

After setting the time of point 7 press the key OFF and the text: temp. of point 1= appears on the first line and one

sets the temperature in

C. on the second line. Temperature is set with the help of keys plus + (to increase the value)

or minus – (to decrease the value) – see paragraph: Adjustment of the required temperature or time: in the chapter

Control algorithms. After setting the temperature of point 1 press the key OFF and in that way temperature of point 1

is saved in the internal memory and after that the text: temp. of point 2= appears on the first line and one sets in the