AKO Electronica AKO-13023 Manuel

Termostat AKO Electronica AKO-13023 için çevrimiçi göz atın veya pdf Manuel indirin. AKO Electronica AKO-13023 2 sayfaları. Thermometers, thermostats and temperature electronic controllers for 58 x 25,4 mm panel cut-out pattern

Sayfayı Yazdır
AKO Electronica AKO-13023 Manuel
1301H201
HOJA TÉCNICA
GB
Thermometers, thermostats and temperature electronic controllers for 58 x 25,4 mm panel cut-out pattern
Small dimensions unit range, designed to monitoring, control and regulating
refrigerating generators (with manual or automatic defrost programmed by
stopping the compressor) or heating generators.
Index:
1- Versions and references

2- Technical data

3- Installation

4- Front panel functions

5- Adjustment and configuration 10- Warnings
1- VERSIONS AND REFERENCES
MODEL
FUNCTION
AKO-13012 Thermometer
AKO-13020 Thermometer
AKO-13023 Thermometer
AKO-13112 Thermostat 16(4) A, 250 V, cos ϕ=1, SPST
AKO-13120 Thermostat 16(4) A, 250 V, cos ϕ=1, SPST 120 V ~ +8% -12%
AKO-13123 Thermostat 16(4) A, 250 V, cos ϕ=1, SPST 230 V ~ ±10%
2- TECHNICAL DATA
Temperature range:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resolution, Set Point and differential:
Input for NTC probe:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controller accuracy:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe tolerance at 25 ºC:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum input power:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Working ambient temperature:
Storage ambient temperature:
Voltage pulse assigned:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure ball test temperature
- Accessible parts:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Active elements positioning parts:
CEM emission voltage test:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CEM emission current test:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control device classification: Independent mounting, with characteristic of
automatic operation action Type 1.B, to be used in clean situation, logical
medium (software) class A.
Double insulation between the power supply, the secondary circuit and the relay output.
3- INSTALLATION
The controller must be installed in a place protected from vibrations, water
and corrosive gases, and where the ambient temperature does not surpass
the value specified in the technical data.
In order the controllers be suitable having IP65 protection, the gasket should
be installed properly between the apparatus and the perimeter of the panel
cut-out where it is to be fitted.
In order to give a correct reading, the probe has to be installed in a place
without heat influences other than the temperature that is to be measured or
controlled.
3.1 Fastening:
PANEL CUT-OUT
58
3.2 Connection:
See diagram in the unit rating plate.
The probe and its lead should NEVER be installed in ducting along with
power, control or power supply wiring.
The power supply circuit should be connected with a minimum 2 A, 230 V,
switch located close to the unit. The cables should be of the type H05VV-F
2x0,75 mm
2
or H05V-K 0,75 mm
Section of connecting wires for relays contacts must be between 1,5 mm
and 2,5 mm
2
4- FRONT PANEL FUNCTIONS
LED 2
LED 1
ON
SET key
When pressed for at least 5 seconds, it displays the SET POINT tem-
perature value, (in thermostats function).
In programming, accept the programmed new value.
LED 1: Defrost in operation indicator. (in thermostats function)
LED 2: Relay ON indicator. (in thermostats function)
LED 2 flashing: Programming phase.
Edición 01
6- Parameters description and messages
9- Maintenance
RELAY
POWER SUPPLY, 50/60 Hz
-
12 V
-
120 V ~ +8% -12%
-
230 V ~ ±10%
12 V
-50 ºC a 99 ºC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
-30 ºC a 70 ºC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
max.
18 mm
3
To fix the unit, place the
2
1
fasteners 1 over the sli-
ders 2 as shown in the
figure. Move the faste-
ners in the direction of
the arrow. By pressing
tab 3 the fasteners may
be moved in the opposi-
te direction of the arrow.
47,5
2
.
UP key
When pressed for at least 5 seconds,
a manual defrost is started with pro-
UP
grammed duration, (in thermostats
key
SET
function).
key
In programming, it increases the dis-
played value.
DOWN
DOWN key
key
In programming, it reduces the dis-
played value.

5- ADJUSTMENT AND CONFIGURATION

It should only be programmed or modified by personnel who are fully con-
versant with operation and possibilities of the equipment.
5.1 Set Point temperature.
The factory SET POINT default value is 0 ºC.
- Press
key for at least 5 seconds to DISPLAY SET POINT. It displays the
CURRENT SET POINT value and LED "2" start flashing.
- Press
or
- Press
key to ACCEPT THE NEW SET POINT. The display returns to the
±20%
current temperature display status and the LED "2" stop flashing.
When PA appears in display, PASSWORD programmed in L5 parameter
should be enter for accede to the CURRENT SET POINT.
±20%
- Press
key. 0 will be displayed to ENTER PASSWORD.
- Press
or
- Press
key to ACCEPT PASSWORD. The CURRENT SET POINT value
will be displayed and possible to be modified.
1 ºC
AKO-149XX
± 1 ºC
± 0,4 ºC
3 VA
5 ºC a 40 ºC
800 V
CURRENT
75 ºC
TEMPERATURE
100 ºC
207 V
9 mA
5.2 Parameters configuration
Level 1 Parameters
- Press
+
be flashing, we are in the LEVEL 1 PARAMETERS and in the display appe-
ar the first parameter "C0".
- Press
key to access the next parameter and
vious one.
- Pressing the
current temperature display status and the LED "2" will stop flashing.
When PA appears in display, PASSWORD programmed in L5 parameter
should be enter for accede to programming LEVEL 1 PARAMETERS.
- Press
key. 0 will be displayed to ENTER PASSWORD.
- Press
or
- Press
key to ACCEPT PASSWORD. The first parameter "C0" will be dis-
played.
Level 2 Values
- To DISPLAY CURRENT VALUE of any parameter, select the required one
and press
or
key.
- Press
key to ACCEPT THE NEW VALUE. The programming returns to
LEVEL 1 PARAMETERS.
CURRENT
TEMPERATURE
10 Sec.
SIMULTANEOUSLY
2
PASSWORD
REQUEST
REMARK: If no key is pressed for 25 seconds in either of the previous steps,
the controller will automatically return to the current temperature display sta-
tus without modifying any of the parameters values.
( 01 de 02 )
www.ako.com
keys for CHANGE SET POINT to the required value.
keys to CHANGE NUMBER and DISPLAY PASSWORD.
IF P2=0
5 Sec.
PASSWORD
ENTER
DISPLAY
REQUEST
PASSWORD
PASSWORD
keys simultaneously for at least 10 seconds. The LED "2" will
key in the last parameter EP, the controller returns to the
keys to CHANGE NUMBER and DISPLAY PASSWORD.
key. Once it is displayed, you can CHANGE VALUE pressing
PASSWORD
IF PROGRAMMED
IF L5=0
ENTER
DISPLAY
PASSWORD
PASSWORD
CURRENT
NEW
SET POINT
SET POINT
key to return to the pre-
LEVEL 1
LEVEL 2
PARAMETERS
VALUES
CURRENT
NEW
VALUE
VALUE
EXIT
PROGRAMMING