DNM RC-32 Kullanıcı El Kitabı - Sayfa 3

Bisiklet Aksesuarları DNM RC-32 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. DNM RC-32 4 sayfaları. Fork

Sayfayı Yazdır

Define your ride type

Trek Bike Ride (TK): Similar to XC ride but not as tough. TK ride includes riding at

slower speed on flatter road without obstacles like rocks, branches or pits. Cross

Country Ride (XC): It includes riding on the hill roads with more obstacles like

rocks, branches and pits. XC ride does not include jump or fall from any heights. XC

bike fork can only be used with professionally designed bike frame and tires. XC

fork and format brake system are compatible. All Mountain Ride (AM): Tougher ride

on harsh environments with larger obstacles. AM Ride does not include jump or

fall from any heights. AM bike fork should only be used with disk brakes and bike

frame, tires and other parts specially designed for AM ride.

"Downhill", "Bumpy" or "Racing"

High speed cycling or downhill bike racing are considered voluntary high risk

activities. Downhill ride and floral cycling both can cause severe accidents. The

speed of biking downhill sometimes can be even faster than motorcycle speed, and

cause similar damage and hazard. Please prepare proper protective equipments,

e.g. helmet covering the whole head, protective item covering whole arms, fingers

and feet. Ask professional technician to check your bike and maintain your bike

thoroughly and more often before each ride (downhill, bumpy or racing).

Install bike fork — Single shoulder base fork

1. Remove the old bike fork from the bike frame.

2. Measure and cut direction turning tube (according to the direction turning tube

of the old bike fork) to match with the front tube of bike frame.

3. Remove the base seal of front tube, then install it on the direction turning tube

of bike fork, until it is fixed on top of the shoulder base according to the

distributor 's instructions.

4.Clean and lubricate the front bowl bearing and base seal according to

distributor 's instructions.

5. Install lower bearing on the fork base seal according to distributor 's

instructions If applicable.

6. Insert direction turning tube into the bowl tube.

7. Install upper bearing, vertical tube bushing and vertical tube.

8. Install vertical tube cover and screws, fasten the screws base on instructions.

9. Install handle, fasten vertical tube screws and fasten unit according to vertical

tube supplier 's instruction.

10. Install and adjust the brakes according to brake supplier 's instructions.

11. Position the quick release parts inside the hook claw holes, fasten it as

instructed to ensure enough screws. Note: Standard hook claw fork is equipped

with two time tire shied hook claw to keep the tire inside the bike fork even when

quick release parts are loosened.

12. Install brake wiring as instructed by the supplier.

Install brake wiring

It can cause severe injury or death if the front brake wire is not properly wired and

firmly connected to the bike fork. The bike fork includes a small black disk brake

wire guider, which can be connected to the fork and used to assist wiring on the

disk brake pliers. The best method is to connect the brake wire through outside of

the left leg of the fork. Make sure the brake wire is not squeezed or touch the tire

in the stroke of bike fork.

Initial setting descending measure (suspension compressed amount caused by

rider 's weight at natural riding position). You need 1 roll meter, bind, 1 pencil, 1

piece of paper and one assistant.

1. Tie a bind on the fork leg, push the bind to the bottom until it reaches the top of

dust proof ring.

2. Ask the rider to ride on the bike at gravity centered position, feet on the pedal.

Let the rider get off the bike and let fork return to its original position.

3.The preload adjust knob is on the spring fork. Turn the knob clockwise to

increase spring preload and reduce descending stroke, turn the knob

counter-clockwise to decrease spring preload and increase descending stroke.

4. Replace new bike parts if descending stroke is still not correct after adjusting

preload or pressure.

Suggested repair interval of All DNM Bike Fork

Under normal use

Short time/ Occasional ride

Clean outer tube of bike fork every six

months, Replace fork parts (e.g.

suspension hydraulic O-ring, springs) at

authorized DNM repair shop every two

years.

Under harsh environment

Short time/ Occasional ride

Clean outer tube of bike fork every six

months, Replace fork parts (e.g.

hydraulic oil, O-ring, Spring) at

authorized DNM repair shop every year.

Long time/ often ride

Clean outer tube of bike fork every six

months, Replace fork parts (e.g.

hydraulic oil, O-ring, Spring) at

authorized DNM repair shop every year.

Long time/ often ride

Clean outer tube of bike fork every

six months, Replace fork parts

(e.g. hydraulic oil, O-ring,

Spring) at authorized DNM repair

shop every 10 months.