ETA Systems PD11VBC Kullanıcı El Kitabı - Sayfa 6

AC Güç Dağıtımı ETA Systems PD11VBC için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. ETA Systems PD11VBC 8 sayfaları. Power protection series

Sayfayı Yazdır

FEATURE OVERVIEW

Switched Outlets Pushbutton:

LED Indicators:

1 of 2 Triggers that can activate a

Status indicator lights

turn-on or shutdown sequence for

for Switched Outlets,

Outlet Bank 2 and High-Current outlets.

DC Voltage Trigger,

Ground OK,

Line Fault

and Unsafe Voltage

15A Circuit Breaker:

Filtered Outlet Bank 1:

Filtered Outlet Bank 2:

Opens in the event that

Four Always-On, Balanced

Four switched, Balanced

equipment plugged into

Double L filtered outlets for

the PD11VBC draws too

audio/video components that

much current. When the

require constant power to

do not require constant power.

white button of the breaker

maintain programmed settings.

is visible, the breaker has

opened. Reduce the load

and push to reset.

IEC Main

Ground Lug:

Voltage Sense

Power

Provides a

Trigger Input:

Receptacle:

common

1/8 inch Mini-Plug jack.

Power cord

grounding point

Connect to a remote trigger

connects to this

for equipment

device that provides 12VDC to

receptacle.

with separate

trigger a startup/shutdown

ground leads.

sequence. This is the second

trigger that will activate the

PD11VBC turn-on or shutdown

sequence. (See switched out-

lets pushbutton on front panel).

1532 Enterprise Pkwy, Twinsburg OH 44087 • (800) 321-6699 • (330) 425-3388 • www.etasys.com

Voltmeter:

Meter Light Dimmer:

Convenience Outlet:

Controls brightness

Backlit analog meter

Provides a quick convenient

of the Voltmeter

measures incoming

way to plug in components

backlighting.

voltage source from

such as camcorders and

0-150 VAC.

video game systems.

High-Current Outlet Bank:

Satellite Coax Jacks:

Two delayed outlets designed for

Two pairs of gold plated

high-current components such as

F-Connectors optimized

amplifiers and powered subwoofers.

for Satellite TV signal

The current available to connected

line protection.

equipment is not limited by the

noise filtration components.

Voltage Sense

High-Current

Outlet Bank 2 Turn-

Trigger Output:

Outlets Turn-On

Off Switch:

1/8 inch Mini-Plug jack.

Switch:

3-position slide switch.

Connecting a 12VDC trig-

3-position slide switch.

Allows adjustment of the

ger to the Voltage Sense

Allows adjustment of

Turn-Off delay for Outlet

Circuit will allow the same

the Turn-On delay for

Bank 2. Choose

signal to pass through the

the two High-Current

between Always-On,

Voltage Sense Output to

Outlets. Choose

10 and 30 seconds.

control the startup/shut-

between 0, 10 and 30

down of an additional

seconds.

device.

FEATURE DETAILS

Cable TV Coax Jacks:

Two pairs of gold plated

F-Connectors optimized for

Cable TV and non-ampli-

fied Rooftop Antenna signal

line protection.

Telephone Jacks:

In/Out connections

for telephone line or

pay-per-view line

protection.

1532 Enterprise Pkwy, Twinsburg OH 44087 • (800) 321-6699 • (330) 425-3388 • www.etasys.com

Coaxial Line Protection

All coaxial cable sheaths from outdoors must be grounded to the building grounding electrode system

where they enter the building (per applicable NEC/CEC code). A driven ground rod is not adequate.

The PD11VBC provides application-specific protection for your satellite and cable TV equipment. Two lines of protection are

provided for each type. The satellite connections are for coaxial cables connected to a DBS (single or dual LNB) satellite

dish. The antenna connection is for a non-amplified rooftop antenna or cable TV line. The Additional TV connection pro-

tects the equipment plugged into the PD11VBC from "backdoor" surges in situations where the video signal runs to anoth-

er room for a downline TV.

Cable TV (Including HDTV) – TV tuners operate at approximately 10 millivolts (0.01 V) and utilize the frequency spec-

trum of 50Mhz to 950Mhz. The clamping level of the PD11VBC's cable TV protection circuitry is 700 millivolts (0.7 volts).

That's less than 1 volt above normal operating levels. The circuitry is shielded to prevent interference and has been opti-

mized to have less than 1dB of signal loss throughout the entire 50Mhz to 950Mhz range.

Satellite - Satellite dish LNB's can require up to 24 volts to operate and utilize the frequency range of 950Mhz to 2.2Ghz.

The clamping level of the PD11VBC's satellite protection circuitry is 27 volts - just 3 volts above the maximum operating

voltage. The circuitry is shielded to prevent interference and has been optimized to have less than 1dB of signal loss

throughout the entire 950Mhz to 2.2Ghz range.

Telephone Line Protection

Satellite TV receivers require a telephone line connection for Pay-Per-View services. The PD11VBC also provides surge pro-

tection for this line. One pair of RJ-11/45 compatible telephone jacks is provided for this. The circuitry utilizes auto-reset-

ting PTCRs and solid-state SIDACtors™ for reliability and unsurpassed protection. The clamping level of the PD11VBC's

telephone protector is 260 volts. This will allow typical ring voltage (90-130VAC) and operating battery voltage (-48DC)

to pass through the circuit and still protect the modem in your satellite receiver from damage.

Please note: The protection circuitry will not work if the phone lines are reversed. The incoming phone cable must be

connected to the "LINE" jack and the cable to the audio/video equipment must be connected to the "EQUIP" jack.

Power Cord

The PD11VBC comes equipped with a UL recognized, 10 foot, IEC320 power cord rated for 120V, 15-Amps, minimum 14

gauge wire and the cord secured to the enclosure with a cord retention bracket. The cord is not intended to be removed.