Etabeta electronics JNR 90L BEAM G Manuel - Sayfa 2

Aydınlatma Ekipmanları Etabeta electronics JNR 90L BEAM G için çevrimiçi göz atın veya pdf Manuel indirin. Etabeta electronics JNR 90L BEAM G 7 sayfaları. Junior

Sayfayı Yazdır
1

SAFETY INSTRUCTIONS

CAU T I O N
Becareful with your operations.With a dangerous voltage you cansuffer a
dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this
condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes written in this user manual.
IMPORTANT
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
If the device has been exposed to temperature changes due to environmental changes,
do not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would
be the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.
During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order
to avoid a hazard.
.01.
122-129
Gobo 5 shake slow to fast
130-137
Gobo 6 shake slow to fast
138-145
Gobo 7 shake slow to fast
146-153
Gobo 8 shake slow to fast
154-161
Gobo 9 shake slow to fast
162-169
Gobo 10 shake slow to fast
170-177
Gobo 11 shake slow to fast
178-185
Gobo 12 shake slow to fast
186-193
Gobo 13 shake slow to fast
194-201
Gobo 14 shake slow to fast
202-209
Gobo 15 shake slow to fast
210-217
Gobo 16 shake slow to fast
218-225
Gobo 17 shake slow to fast
226-255
Rot. gobo wheel cont. rotation slow to fast
0-31
Shutter closed
32-63
Shutter open
64-95
Strobe effect slow to fast
96-127
Shutter open
7
5
Shutter
128-159
Pulse-effect in sequences slow to fast
160-191
Shutter open
192-223
Random strobe effect slow to fast
224-255
Shutter open
0-255
Dimmer 0%...100%
8
6
Dimmer
0-255
In(near)to out(far)
9
7
Focus
0-5
OFF
6-127
ON
10
8
Prism
128-255
Rotating from slow to fast
0-225
Max to min speed
11
9
Speed
226-235
Blackout by movement
pan/tilt
236-245
Blackout by all wheel changing
246-255
No function
0-19
No function
20-29
No function
30-39
No function
40-79
No function
80-84
All motor reset
85-87
Scan motor reset
88-90
Colors motor reset
91-93
Gobo motor reset
94-96
Shutter&Dimmer motor reset
12
10
Special
97-99
Other motor reset
function
100-119
Internal program 1
120-139
Internal program 2
140-159
Internal program 3
160-179
Internal program 4
180-199
Internal program 5
200-219
Internal program 6
220-239
Internal program 7
240-255
Internal sound program 1
.10.