DOD TEC4X Kullanıcı Kılavuzu - Sayfa 2

Kayıt Ekipmanları DOD TEC4X için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. DOD TEC4X 8 sayfaları. Multi-effects
Ayrıca DOD TEC4X için: Kullanıcı Kılavuzu (8 sayfalar)

Sayfayı Yazdır

DECLARATION OF CONFORMITY

Manufacturer's Name:

DOD Electronics

Manufacturer's Address:

8760 S. Sandy Parkway

Sandy, Utah 84070, USA

declares that the product:

Product Name:

Tec4X

Product Options:

All (requires a Class II power adapter that conforms to the requirements of EN 60065, EN

60742, or equivalent).

conforms to the following product specifications:

Safety:

EN 60065 (1993) IEC 65 (1985) with Amendments 1,2,3

EMC:

EN 55013: (1990) EN 55020: (1991)

Supplementary Information:

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC

as amended by directive 93/68/EEC.

DOD Electronics

President

8760 S. Sandy Parkway

Sandy, Utah 84070, USA

Effective: (4/13/98)

European Contact: Your Local DOD Sales and Service Office or

International Sales Office

3 Overlook Drive #4

Amherst, New Hampshire 03031, USA

Tel: (603) 672-4244

Fax: (603) 672-4246

C A U T I O N

R I S K O F E L E C T R I C S H O C K

D O N O T O P E N

A T T E N T I O N :

R I S Q U E D E C H O C E L E C T R I Q U E - N E P A S O U V R I R

W A R N I N G :

T O R E D U C E T H E R I S K O F F I R E O R E L E C T R I C

S H O C K D O N O T E X P O S E T H I S E Q U I P M E N T T O R A I N O R M O I S T U R E

These symbols are internationally accepted symbols that warn of potential haz-

ards with electrical products. The lightning flash means that there are danger-

ous voltages present within the unit. The exclamation point indicates that it is

necessary for the user to refer to the owner's manual.

These symbols warn that there are no user serviceable parts inside the unit.

Do not open the unit. Do not attempt to service the unit yourself. Refer all ser-

vicing to qualified personnel. Opening the chassis for any reason will void the

manufacturer's warranty. Do not get the unit wet. If liquid is spilled on the unit,

shut it off immediately and take it to a dealer for service. Disconnect the unit

during storms to prevent damage.

U.K. MAINS PLUG WARNING

A moulded mains plug that has been cut off from the cord is unsafe. Discard the

mains plug at a suitable disposal facility. NEVER UNDER ANY CIRCUM-

STANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO

A 13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover

in place. Replacement fuse covers can be obtained from your local retailer.

Replacement fuses are 13 amps and MUST be ASTA approved to BS1362.

WARNING

FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:

WATER AND MOISTURE: Appliance should not be used near water (e.g. near a

bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming

pool, etc). Care should be taken so that objects do not fall and liquids are not spilled

into the enclosure through openings.

POWER SOURCES: The appliance should be connected to a power supply only of

the type described in the operating instructions or as marked on the appliance.

GROUNDING OR POLARIZATION: Precautions should be taken so that the ground-

ing or polarization means of an appliance is not defeated.

POWER CORD PROTECTION: Power supply cords should be routed so that they are

not likely to be walked on or pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience receptacles, and the point where

they exit from the appliance.

SERVICING: To reduce the risk of fire or electric shock, the user should not attempt

to service the appliance beyond that described in the operating instructions. All other

servicing should be referred to qualified service personnel.

FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE:

Replace fuse with same type and rating only.

ELECTROMAGNETIC COMPATIBILITY

Operation is subject to the following conditions:

• this device may not cause harmful interference, and

• this device must accept any interference received, including interference

that may cause undesired operation.

• use only shielded interconnecting cables.

• operation of this unit within significant electromagnetic fields should be

avoided.