Dodge BU483 Kullanım Kılavuzu

Endüstriyel Ekipmanlar Dodge BU483 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Dodge BU483 8 sayfaları.

Dodge® Quantis® Ultra Kleen RHB Reducer

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of

printing. Please see dodgeindustrial.com for updated instruction manuals.

WARNING: To ensure the drive is not unexpectedly started, turn off and

lock-out or tag power source before proceeding. Failure to observe these

precautions could result in bodily injury.

WARNING: All products over 25 kg (55 lbs) are noted on the shipping

package. Proper lifting practices are required for these products.

WARNING: High voltage and rotating parts can cause serious

or fatal injury and property damage. The use of electrical

machinery, like all other utilization of concentrated power and

rotating equipment, can be hazardous. Installation, operation and

maintenance should be performed only by qualified electrical and

mechanical maintenance personnel familiar with NEMA safety

standards, the National Electrical Code and sound local practices.

The manual is to be studied thoroughly by personnel responsible

for the installation and maintenance of this equipment before

installation is begun. Personnel must be familiar with the potential

hazards involved. If this warning is not observed, personal injury

and/or property damage may result. Keep this document for future

reference.

WARNING: Depending on operating conditions, sound levels for

Quantis products may exceed 70 dB. Protective measures such

as hearing protection may be needed when in close proximity to a

Quantis Reducer in operation.

WARNING: The Dodge Quantis UK RHB and its connected

equipment and accessories must be guarded. Rotating parts such

as couplings, pulleys, fans and unused shaft extensions must

be permanently guarded by the user against accidental contact

with personnel and their clothing. The surface temperature of the

Dodge Quantis UK RHB enclosure may reach temperatures which

can cause discomfort or injury to personnel accidentally coming

into contact with hot surfaces. The user should provide guards

to prevent accidental contact with hot surfaces. Guards must be

sufficiently rigid to maintain adequate guarding in normal service.

WARNING: Because of the possible danger to person(s) or property

from accidents which may result from the improper use of products,

it is important that correct procedures be followed. Products must be

used in accordance with the engineering information specified in the

catalog. Proper installation, maintenance and operation procedures

must be observed. The instructions in the instruction manuals must

be followed. Inspections should be made as necessary to assure

safe operation under prevailing conditions. Proper guards and other

suitable safety devices or procedures as may be desirable or as may

be specified in safety codes should be provided, and are neither

provided by Dodge nor are the responsibility of Dodge. This unit and

its associated equipment must be installed, adjusted and maintained

by qualified personnel who are familiar with the construction and

operation of all equipment in the system and the potential hazards

involved. When risk to persons or property may be involved, a holding

device must be an integral part of the driven equipment beyond the

speed reducer output shaft.

Gearmotors, C-Face Reducers, Separates

Instruction Manual

Sizes 38-48

WARNING: Quantis products exceeding 30 lb (13.5 kg) should be

lifted using lift-assist equipment rated for the weight of the product.

Weight values for all Quantis products are listed in the Gearing

Engineering Catalog. Lifting brackets provided on Quantis should

be used when connecting to lift-assist equipment.

WARNING: Threaded hardware used to mount the The Dodge

Quantis UK RHB Unit must be 18-8 Stainless or Metric A-2

Stainless. DO NOT USE HARDWARE OF A LOWER GRADE.

GENERAL

Please read these instructions carefully. They contain vital

information on proper installation, operation, maintenance

and service for the Dodge Quantis Ultra Kleen (UK) RHB gear

reducer.

Each Dodge gear reducer is thoroughly inspected and tested at

the factory prior to shipment. Care is taken in packing of each

gear reducer. However, each gear reducer should be thoroughly

inspected before it is accepted from the transportation company.

If any of the goods called for in the bill of lading are damaged

or missing, do not accept the shipment until the freight agent

makes appropriate notation on your freight bill. If any loss or

damage is discovered later, notify the agent at once and request

an inspection. Though Dodge Mechanical Power Transmission

Company, Inc. will be happy to assist you with claims for loss or

damage in shipment, the transportation company is responsible

for reimbursing you for such claims. Claims for loss or damage

in shipment must not be deducted from the Dodge Mechanical

Power Transmission Company, Inc. invoice, nor should payment

of the Dodge Mechanical Power Transmission Company, Inc.

invoice be withheld awaiting claims adjustment. The carrier, not

Dodge, guarantees safe delivery. If considerable damage or

shortage has occurred and the situation is urgent, contact the

nearest Dodge Sales Office.

WARRANTY

NOTE: Service and repair under warranty should be performed

only by an Dodge Mechanical Power Transmission Company,

Inc. Authorized Service Shop. Contact Dodge Mechanical Power

Transmission Company, Inc. Product Support for Assistance.

The Dodge Quantis UK RHB is warranted under the Dodge

Mechanical Power Transmission Company, Inc. "Standard

Terms and Conditions of Sale". Warranty claims must be

submitted to Dodge Mechanical Power Transmission Company,

Inc. within one year from the date of installation or within three

years from the date of manufacture, whichever comes first. The

warranty does not extend to failures induced by misuse, improper

storage or handling, abuse, or misapplication.