Dodge SLEEVOIL RXT Kullanım Kılavuzu - Sayfa 5
Endüstriyel Ekipmanlar Dodge SLEEVOIL RXT için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Dodge SLEEVOIL RXT 12 sayfaları. Pillow blocks with self lubrication
Ayrıca Dodge SLEEVOIL RXT için: Kullanım Kılavuzu (12 sayfalar)
Sayfayı Yazdır
Assemble each seal around shaft and torque clamp screws to
value specified in Table 6.
Align seals per values given in Table 6.
NOTE: Check the construction drawing for seal size and
position as three different seal bore sizes can be used on
any housing. Seals can be reversed depending on shaft
configuration and spacing.
Table 6 – Shaft to Seal Clearance (inches)
Shaft
2-15/16
3-7/16
Diameter
Bottom of
.001
.001
Shaft to
Seal
Side of
.003
.003
Shaft to
.006
.006
Seal
Shaft
6
7
Diameter
Bottom of
.002
.002
Shaft to
Seal
Side of
.006
.007
Shaft
.009
.010
to Seal
Table 7 - Torque Values for Seal Hardware (in. - lbs.)
Housing
3
4
Size
Clamp
12
12
Screws
Mounting
40
40
Screws
Torque seal mounting screws to value given in Table 7.
Assemble well-nut, washer and screw
Install well-nut in drain hole on outer face of seal. Tighten screw
until well-nut is tight in hole.
3-15/16
4-7/16
4-15/16
.001
.001
.001
.004
.004
.005
.007
.007
.008
8
9
10
12
.002
.002
.003
.003
.008
.009
.010
.012
.011
.012
.013
.015
5
6
8
12
25
45
40
40
40
7. MISCELLANEOUS INSTRUCTIONS
Remove all unused pipe plugs, apply sealant and replace. Tighten
securely. Install oil sight gauge in specified location.
SEAL/SHAFT
CLEARANCE
5-7/16
.001
.005
.008
14-1/2
Note: Each housing base has two pre-drilled holes for
doweling housing to pedestal.
.003
8. LUBRICATION AND OPERATION
Fill pillow block with the amount of oil specified in Table 8.
.014
.018
Housing Size
10
45
40
10
NOTE: Since the satisfactory operation of the pillow block
depends almost entirely on the oil film being maintained
between the shaft and bearing liner surface, use a high
grade straight mineral oil with rust and oxidation (R & O)
inhibitors and antifoam agents. Oil viscosity is determined by
the equipment manufacturer and normally specified on the
construction drawing or in the operating manual. Information
regarding qualities and properties of specific oils should be
referred to the lubricant manufacturer.
Approximate viscosity:
ISO 32 — 158 SUS at 100ºF; 44 SUS at 210ºF
ISO 68 — 335 SUS at 100ºF; 55 SUS at 210ºF
ISO 100 — 495 SUS at 100ºF; 66 SUS at 210ºF
5
Table 8 - Housing Oil Sump Capacity
Oil Capacity in Gallons (Quarts)
3
4
5
6
8
1-1/4 (5)
1-7/8 (7-1/2)
2-1/2 (10)
3-1/4 (13)
5-1/8 (20-1/2)
7-3/4 (31)