Doheny's DWC134 Kurulum Talimatları - Sayfa 2

Aydınlatma Ekipmanları Doheny's DWC134 için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. Doheny's DWC134 2 sayfaları. Solid winter cover, mesh winter cover

Sayfayı Yazdır

General Procedures

1. Since the cover is designed to rest on the pool's water, it is important to be sure your

pool is not leaking prior to installation.

2. Your cover is made from extremely strong and durable material. However it is required

that your cover be protected from sharp corners, rough edges, or any hard

surfaces that may cause abrasion. Padding, such as old towels, foam remnants, or

other similar material, are recommended.

3. It is important that covers be installed properly and snugly so that the wind will not

cause damage to the cover by getting under the cover and causing it to billow or flap.

Inground Pool Installation

1. Be sure that the cover will be supported by the water in the pool and that the cover is

not in direct contact with any sharp, rough or abrasive surfaces.

2. Lower the water level in your pool below the skimmer. (No more than 18" below coping.)

3. Place the cover on the ground and spread evenly over the pool.

4. Insert unfilled water bags into the water bag loops (for covers without loops, lay the

water bags directly on to the outside perimeter of the cover.)

5. The water bags must cover the entire perimeter of the cover to prevent wind from

getting under the cover and causing the cover to billow or flap. Caution, such billowing

or flapping in the wind can cause serious damage to your cover. Therefore, be sure

the water bags are placed end-to-end (See Figure 1).

6. Fill the water bags. If you are in an area of extreme cold, fill the water bags only half full

to allow for ice expansion.

General Procedures

1. Be sure your pool is not leaking prior to installation.

2. Your cover is made from extremely strong and durable material. However it is required

that your cover be protected from sharp corners, rough edges, or any hard

surfaces that may cause abrasion. Padding, such as old towels, foam remnants, or

other similar material, are recommended.

3. It is important that covers be installed properly and snugly so that the wind will not

cause damage to the cover by getting under the cover and causing it to billow or flap.

Inground Pool Installation

1. Be sure that the cover is not in direct contact with any sharp, rough or abrasive surfaces.

2. Lower the water level in your pool below the skimmer. (No more than 18" below coping.)

3. Place the cover on the ground and spread evenly over the pool. Cover should be slightly

suspended above pool water allowing room for water drainage. Adjust cover if pool

water level rises.

4. Insert unfilled water bags into the water bag loops (for covers without loops, lay the

water bags directly on to the outside perimeter of the cover.)

5. The water bags must cover the entire perimeter of the cover to prevent wind from

getting under the cover and causing the cover to billow or flap. Caution, such billowing

or flapping in the wind can cause serious damage to your cover. Therefore, be sure

the water bags are placed end-to-end (See Figure 1).

6. Fill the water bags. If you are in an area of extreme cold, fill the water bags only half full

to allow for ice expansion.

Solid Winter Cover Installation Instructions

Mesh Winter Cover Installation Instructions

Above Ground Pool Installation

1. Be sure that the cover will be supported by the water in the pool and that the cover is

not in direct contact with any sharp, rough, or abrasive surfaces.

2. Lay out the cover on the ground. Thread cable through the grommets (or loops). The

cable must remain on the outside of the cover, except between the pairs of grommets (See

Figure 2).

3. Insert one cable end through the hole at one end of the ratchet and into the center

spindle. Turn the spindle a few times to secure the cable. Insert the other cable end

through the other hole in the ratchet and pull the cable through the spindle as far as it

will go. Turn the ratchet handle to tighten the cable. Make sure cable lies on the outside

of the cover all around the pool except where it goes through the pairs of grommets. The

cable must fit tightly against the wall of the pool to prevent wind from getting

underneath the cover. To loosen or remove cable, press lever on top of ratchet and turn

handle in the opposite direction (See Figure 5).

4. Before placing cover over the pool, pool water should not be less than 6" from top of

pool. Where a through-the-wall skimmer is used, cover up the skimmer opening. Inflate

flotation pillow (available from your dealer) and secure the pillow in center of pool by

tying grommeted ends with nylon rope to pool sidewall. Place the cover over pillow to

form a loose pyramid letting the cover fall on the water around the circumference (See

Figure 6). Pull end of cover over pool wall. It is important that the cover fits snugly

against the wall to prevent wind from getting under the cover and causing the cover

to billow and flap. Caution, such billowing and flapping can cause serious damage to

the cover. If you cannot get a snug fit you must block any openings between the cover

and the pool wall.

Above Ground Pool Installation

1. Be sure that the cover is not in direct contact with any sharp, rough, or abrasive

surfaces.

2. Lay out the cover on the ground. Thread the cable through the grommets (or loops).

The cable must remain on the outside of the cover, except between the pairs of

grommets (See Figure 2).