Doheny's 90500 Kurulum, Çalıştırma ve Parçalar - Sayfa 3
Su Pompası Doheny's 90500 için çevrimiçi göz atın veya pdf Kurulum, Çalıştırma ve Parçalar indirin. Doheny's 90500 8 sayfaları. Inground vs pumps
Sayfayı Yazdır
CHAPTER 4
:
STOP AND RUN THE PUMP
Start the Pump
1. Make sure the pump is connected with electricity.
When power is on, the display screen will display
the time.
2. Press one of ECO/CLEAN/BOOST, the pump will
run. The light on the corresponding program will be
lit. No matter what program you select, the pump will
run on 2850RPM for 5 minutes to eliminate the air in
the pump, so the impeller will not dry grind thus to
cause leakage. After high-speed running, the pump
will run the default speed of the selected program.
Stop the Pump
1. Press STOP of the running pump, the pump will
stop. The lights on the screen twinkle.
Change Pump Running Speed
1. When the pump is running ECO/CLEAN/BOOST,
press arrow buttons up or down to change the speed,
each press is for 50RPM. It will save automatically,
no need to press ENTER.
2. Switch between ECO/CLEAN/BOOST during pump
operation, the pump will not run 5 minutes high
speed again.
3. For MODE 1 and MODE 2, to change speed of S1
and S3, first press CLEAN, if not work, you will
need to stop the pump first. After 5 minutes high
speed running, press CLEAN, then press arrow
button to increase or decrease RPM. When press
MODE 1 or MODE 2 again to run the pump, S1 and
S3 will run as just selected.
To adjust S2 and S4, first press ECO, if not work,
you will need to stop the pump. After 10 minutes
high speed running, press ECO, then press arrow
button to increase or decrease RPM . When press
MODE 1 or MODE 2 again, S2 and S4 will run as
just selected.
NOTE: RPM for S2 and S4 or S1 and S3 are always
the same. The default for S1 and S3 is 2400RPM, the
adjustable range is 2400 to 2850RPM. The default for
S2 and S4 is 1500RPM.The adjustable range is 1000
to 2400PRM.
10411 80th Avenue Pleasant Prairie, WI 53158 | Orders and Customer Care: 1-800-574-7665 | Fax: 1-800-323-5932 | Doheny.com
Pump Run Under Pre-Programmed Conditions
Pump has three quick start button ECO / CLEAN /
BOOST, as below image. The default speed is 1500,
2400, 3250RPM respectively.
1. Be sure the pump is power on.
2. Press one of ECO/CLEAN/BOOST, the LED light
on screen will be lit.
3. The screen will display STUP for 1 second, and run
2850PRM for 5 minutes. After 10 minutes, the
pump will run on the selected speed.
Indicator Light
ECO
1000-2400RPM
Default: 1500
CHAPTER 5
:
PUMP RUN UNDER MODE1 / MODE2
Mode 1 / Mode 2 Introduction
Running hours and RPMS are all adjustable.
MODE 1 - 16 Hour Running Cycle
Stage
Start
Running
Time
Hour
S1
6:00
3
am
adjustable
S2
9:00
5
am
adjustable
S3
6:00
3
pm
adjustable
S4
9:00
5
pm
adjustable
MODE 2 - 24 Hour Running Cycle
Stage
Start
Running
Time
Hour
S1
12:00
6
pm
adjustable
S2
6:00
3
am
adjustable
S3
9:00
9
am
adjustable
S4
6:00
6
pm
adjustable
CLEAN
BOOST
2400-2850RPM
2850-3450RPM
Default: 2400
Default: 3250
Default
Quick
Speed
2400 RPM
CLEAN
1500 RPM
2400 RPM
CLEAN
1500 RPM
Default
Quick
Speed
1500 RPM
2400 RPM
CLEAN
1500 RPM
2400 RPM
CLEAN
Start
ECO
ECO
Start
ECO
ECO