Dolby Laboratories CP650 Kullanıcı Kılavuzu - Sayfa 2

İşlemci Dolby Laboratories CP650 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Dolby Laboratories CP650 3 sayfaları. Digital cinema processor
Ayrıca Dolby Laboratories CP650 için: Şartname Sayfası (2 sayfalar), Şartname Sayfası (4 sayfalar)

Sayfayı Yazdır

Projector 1

Cat. No. 701

Digital Reader

Inboard Digital

Basement Reader

Cable Part Numbers:

Projector 2

83141 (30 feet) (9.1 meters)

83237 (50 feet) (16.2 meters)

SHIELD

GROUND

MUTE

To Automation

NONSYNC

(See Interface Requirements

in Appendix B)

U L

LISTED

PROFESSIONAL AUDIO

EQUIPMENT

4J06

100 - 240 Vac 50 - 60 Hz 120 W

CAUTION

To reduce the risk of fire

replace only with same

type and rating

250V time-lag fuse.

FUSE T 6.3A L

5 mm x 20 mm

Pass wire through strain

relief and chassis access

hole. Tighten inside nut

Remote Control Unit Cat. No. 779 or

finger tight.

Remote Fader Cat. No. 771

Customer Supplied

100k Linear Pot

Front View of Pot

Notes:

Follow all local electrical and building codes.

Use grounded (earthed) conduit wherever possible. Avoid

routing signal wiring near electric motors, rectifiers, power

wiring, dimmer wiring, or other sources of electrical noise.

For two conductor with shield wiring, use Belden 8451

2-conductor shielded cable or equivalent: tinned copper,

twisted pair, 22 AWG stranded tinned copper drain wire,

aluminum-polyester shield, 100% shield coverage,

conductor-to-conductor 111 pF per meter.

CP650 Installation Manual

2-Projector Changeover

Projector 1

Projector Changeover Relays,

Pulsed Contacts

Open

Closed

50 ms

minimum

Projector 2

Projector Changeover Relay

Maintained Closed Contact

Selects Projector 2

For Dolby Digital Installations

Proj 1 Motor Start Relay

Projector Motor

Proj 2 Motor Start Relay

Projector Motor

AUTOMATION

Digital Cinema Processor

San Francisco U.S.

Wootton Bassett U.K.

MUTE

READER 1

NONSYNC

REMOTES AND AUD. FADER

Dolby Digital

READER 2

NONSYNC IN 1

REMOTE

DATA

L +

FADER

N/C

H/I OUTPUT

R +

NONSYNC IN 2

Ls +

Rs +

SW +

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this

23 24 25

MAIN AUDIO OUTPUT

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

This Class A digital apparatus complies with Canadian ICES003.

DATA

GND

For three conductor with shield wiring, use Belden 8771

3-conductor shielded cable or equivalent: tinned copper,

twisted pair, 22 AWG stranded tinned copper drain wire,

aluminum-polyester shield, 100% shield coverage,

conductor-to-conductor 75 pF per meter.

All shields must be connected to the CHASSIS of the CP650.

This achieves the required RF interference immunity. A metal

housing must be used for all D-connectors and the shields

must be connected to the housing. Chassis ground and circuit

(audio) ground are internally connected.

Single Projector

(shipped installed on unit)

All shields must be connected

to the metal shield of the D-connector.

For future

Automation use

SERIAL DATA

CP650

(RS-232)

MIC. INPUT

ETHERNET

MOTOR START

OPTION CARD I/O

MS1

P1/ P2

MS2

WARNING

Risk of electric shock.

Do not open.

OPTICAL IN 1

No user serviceable parts

inside. Refer all service

to qualified personnel.

This equipment must be

earthed/grounded.

6-CH AUDIO INPUT

OPTICAL IN 2

(External Digital Processor)

FB425A01.CDR

CD, Tape, etc.

Non-Sync 2

Non-Sync 1

2-9

Installation

15 V phantom power switchable via front

setup control panel dip switch number 3.

PA Microphone 1

(Or Mic-multiplexer

for setup)

Jumper Plug

Non-Sync Source

With 2-channel AES/EBU

Digital Output (Format 80)

black

red

Reverse Scan / LED

Analog Reader Board

red

black

red

black

The physical board mounting in the projector and

the connector

orientation

4 2

appears on which pin of the connector.

that pin allocations for the channels will vary

depending on mounting arrangements of the

board and connector

solder hole with a square outline is pin 1.

Projector 1

OR:

Projector 2

red

black

red

black

4 3

9 8 7

SHIELD

6-Channel Analog Input

(all unlabeled pins are signal ground)

(normal operating level = 300 mV)

CP650 INSTALLATION WIRING

INPUT AND CONTROL CONNECTIONS

red

black

OUT 1 +

OUT 1 -

OUT 2 +

OUT 2 -

affect which channel

Be aware

. The J2 connector pin

Solar Cell

green

black

red