Cypress Semiconductor CY7C1302DV25 Şartname Sayfası - Sayfa 6

Bilgisayar Donanımı Cypress Semiconductor CY7C1302DV25 için çevrimiçi göz atın veya pdf Şartname Sayfası indirin. Cypress Semiconductor CY7C1302DV25 19 sayfaları. Cypress 9-mbit burst of two pipelined srams with qdrtm architecture specification sheet

Sayfayı Yazdır

IEEE 1149.1 Serial Boundary Scan (JTAG)

These SRAMs incorporate a serial boundary scan test access

port (TAP) in the FBGA package. This part is fully compliant

with IEEE Standard #1149.1-1900. The TAP operates using

JEDEC standard 2.5V I/O logic levels.

Disabling the JTAG Feature

It is possible to operate the SRAM without using the JTAG

feature. To disable the TAP controller, TCK must be tied LOW

) to prevent clocking of the device. TDI and TMS are inter-

nally pulled up and may be unconnected. They may alternately

be connected to V

through a pull-up resistor. TDO should

be left unconnected. Upon power-up, the device will come up

in a reset state which will not interfere with the operation of the

device.

Test Access Port—Test Clock

The test clock is used only with the TAP controller. All inputs

are captured on the rising edge of TCK. All outputs are driven

from the falling edge of TCK.

Test Mode Select

The TMS input is used to give commands to the TAP controller

and is sampled on the rising edge of TCK. It is allowable to

leave this pin unconnected if the TAP is not used. The pin is

pulled up internally, resulting in a logic HIGH level.

Test Data-In (TDI)

The TDI pin is used to serially input information into the

registers and can be connected to the input of any of the

registers. The register between TDI and TDO is chosen by the

instruction that is loaded into the TAP instruction register. For

information on loading the instruction register, see the TAP

Controller State Diagram. TDI is internally pulled up and can

be unconnected if the TAP is unused in an application. TDI is

connected to the most significant bit (MSB) on any register.

Test Data-Out (TDO)

The TDO output pin is used to serially clock data-out from the

registers. The output is active depending upon the current

state of the TAP state machine (see Instruction codes). The

output changes on the falling edge of TCK. TDO is connected

to the least significant bit (LSB) of any register.

Performing a TAP Reset

A Reset is performed by forcing TMS HIGH (V

edges of TCK. This RESET does not affect the operation of

the SRAM and may be performed while the SRAM is

operating. At power-up, the TAP is reset internally to ensure

that TDO comes up in a high-Z state.

TAP Registers

Registers are connected between the TDI and TDO pins and

allow data to be scanned into and out of the SRAM test

circuitry. Only one register can be selected at a time through

the instruction registers. Data is serially loaded into the TDI pin

on the rising edge of TCK. Data is output on the TDO pin on

the falling edge of TCK.

Instruction Register

Three-bit instructions can be serially loaded into the instruction

Document #: 38-05625 Rev. *A

TDI and TDO pins as shown in TAP Controller Block Diagram.

Upon power-up, the instruction register is loaded with the

IDCODE instruction. It is also loaded with the IDCODE

instruction if the controller is placed in a reset state as

described in the previous section.

When the TAP controller is in the Capture IR state, the two

least significant bits are loaded with a binary "01" pattern to

allow for fault isolation of the board level serial test path.

Bypass Register

To save time when serially shifting data through registers, it is

sometimes advantageous to skip certain chips. The bypass

and TDO pins. This allows data to be shifted through the

SRAM with minimal delay. The bypass register is set LOW

) when the BYPASS instruction is executed.

Boundary Scan Register

The boundary scan register is connected to all of the input and

output pins on the SRAM. Several no connect (NC) pins are

also included in the scan register to reserve pins for higher

density devices.

The boundary scan register is loaded with the contents of the

RAM Input and Output ring when the TAP controller is in the

Capture-DR state and is then placed between the TDI and

TDO pins when the controller is moved to the Shift-DR state.

The EXTEST, SAMPLE/PRELOAD and SAMPLE Z instruc-

tions can be used to capture the contents of the Input and

Output ring.

The Boundary Scan Order tables show the order in which the

bits are connected. Each bit corresponds to one of the bumps

on the SRAM package. The MSB of the register is connected

to TDI, and the LSB is connected to TDO.

Identification (ID) Register

The ID register is loaded with a vendor-specific, 32-bit code

during the Capture-DR state when the IDCODE command is

loaded in the instruction register. The IDCODE is hardwired

into the SRAM and can be shifted out when the TAP controller

is in the Shift-DR state. The ID register has a vendor code and

other information described in the Identification Register

Definitions table.

TAP Instruction Set

Eight different instructions are possible with the three-bit

instruction register. All combinations are listed in the

) for five rising

Instruction Code table. Three of these instructions are listed

as RESERVED and should not be used. The other five instruc-

tions are described in detail below.

Instructions are loaded into the TAP controller during the

Shift-IR state when the instruction register is placed between

TDI and TDO. During this state, instructions are shifted

through the instruction register through the TDI and TDO pins.

To execute the instruction once it is shifted in, the TAP

controller needs to be moved into the Update-IR state.

IDCODE

The IDCODE instruction causes a vendor-specific, 32-bit code

to be loaded into the instruction register. It also places the

instruction register between the TDI and TDO pins and allows

the IDCODE to be shifted out of the device when the TAP

controller enters the Shift-DR state. The IDCODE instruction

CY7C1302DV25

Page 6 of 18

[+] Feedback